Quick Start Guide 1 Insert the batteries into the remote control Lift the cover on the back of the remote upward gently. Install two AAA batteries. Make sure to match the + and - ends of the batteries in the battery compartment (observe the correct polarity) Replace the cover. 4 Connect the power cord to the 220-240V AC, 50 Hz. To switch on the TV from standby mode either: 1. Press the " " button, P+ / P- or a numeric button on the remote control. 2. Press the side function switch until the TV comes on from standby. 5 2 Connect the Aerial/Cable straight to your TV Aerial or Cable 3 Connect the TV to the mains socket insert plug... To switch the TV on HDMI input You can activate Store mode option to be available in "Other settings" menu and your TV's features will be illustrated on the top of the screen. A confirmation screen will be displayed. Select YES to proceed. If Home Mode is selected, Store mode will not be available after the First Time Installation. Press OK button to continue. Aerial Installation PLEASE ENSURE BOTH UNITS ARE SWITCHED If you select AERIAL option from the Search Type OFF BEFORE CONNECTING. Use a HDMI to HDMI screen, the television will search for digital terrestrial cable to connect the two units together. To select the TV broadcasts. HDMI input, press the SOURCE button on the remote Note: You can press MENU button to cancel. control. Each time it is pressed, the on-screen menu After all the available stations are stored, the Channel confirms your selection. List will be displayed on the screen. If you like how the channels are sorted according to the LCN (*), please To HDMI connection on select "Yes" and then press OK. the device Press MENU button to quit channel list and watch TV. (*) LCN is the Logical Channel Number system that organizes available broadcasts in accordance with a recognizable channel sequence (if available). 6 Start Auto Setup procedure IMPORTANT: Ensure that the aerial/cable connected and a Common Interface module is not inserted before switching on the TV for the first time installation. Do not insert a common interface module during the search process. When turned on for the first time, the language selection screen is displayed. Select the desired language and press OK. First Time Installation (FTI) screen will be displayed next. Set your preferences using the navigation buttons and when finished, press OK to continue. Cable Installation If you select CABLE option and press OK button on the remote control. To continue, please select YES and press OK. To cancel operation, select NO and press OK. You can select frequency ranges from this screen. Enter the frequency range manually by using the numeric button. Note: Searching duration will change depending on the selected search step.
Snabbstartsguide 1 Sätt in batterierna i fjärrkontrollen Lyft försiktigt upp locket på baksidan av fjärrkontrollen. Sätt i två AAA-batterier. Se till att matcha batteriernas + och - i batterifacket (notera polariteten). 4 Anslut nätsladden till eluttaget på 220-240 V AC, 50 Hz. För att sätta på TV:n från viloläget kan du antingen: 1. Trycka på " "-knappen, P+/P- eller en sifferknapp på fjärrkontrollen. 2. Tryck på funktionen för sidväxlaren till dess TV:n hamnar i viloläge. 5 2 För att slå på TV:n HDMI-ingång SÄKERSTÄLL ATT BÄGGE APPARATERNA ÄR AVSTÄNGDA FÖRE ANSLUTNING. Använd en Anslut antennen/kabeln direkt till din TV HDMI till HDMI-kabel för att ansluta de två enheterna. För att välja HDMI-ingången, tryck på knappen SOURCE (Källa) på fjärrkontrollen. Varje Antenn eller kabel gång som den trycks ned, bekräftar skärmmenyn ditt val. Till HDMI-anslutning på apparaten 3 Anslut TV:n till eluttaget Sätt i kontakt... 6 Starta den automatiska inställningsproceduren VIKTIGT! Se till att antennen/kabeln är ansluten och en CI-modul inte är inkopplad innan du sätter på TV:n för den första installationen. Sätt inte i en CI-modul under sökningen. När TV:n slås på första gången visas menyn språkval. Välj det önskade språket och tryck på OK. Skärmen för förstagångsinstallationen kommer visas härnäst. Ställ in egenskaperna med hjälp av navigeringknapparna och när du är klar trycker du på OK för att fortsätta. Du kan aktivera alternativet Store-läge så att det finns tillgängligt under menyn "Other settings" (andra inställningar) så visas TV:ns bilder överst på skärmen. En dialogruta för bekräftelse visas. Välj "YES" (Ja) för att fortsätta. Om det "avaktiveras" kommer butiksläge inte vara tillgängligt efter förstagångsinstallationen. Tryck på OK-knappen för att fortsätta. Antenninstallation Om du väljer söktypen AERIAL (ANTENN) kommer TV:n att söka efter digitala, markbundna sändningar. Anm.: Du kan trycka på knappen MENY för att avbryta. Efter att alla tillgängliga stationer sparats kommer kanallistan att visas på skärmen. Om du vill sortera kanalerna, i enlighet med LCN, välj Ja och tryck sedan på OK. Tryck på OK-knappen för att lämna kanallistan och titta på TV. (*) LCN är det logiska kanalnummersystemet som ordnar tillgängliga sändningar i enlighet med en igenkännbar kanalsekvens (om tillgänglig). Kabelinstallation Om du väljer alternativet Kabel och trycker på OKknappen på fjärrkontrollen. Välj YES (Ja) och tryck på OK för att fortsätta. Välj NO (Nej) och tryck på OK för att avbryta. Du kan välja frekvensomfång på den här skärmen. Ange frekvensintervallet manuellt genom att använda de numeriska knapparna. Anm.: Söktiden kommer förändras beroende på det valda söksteget.