ASSEMBLY INSTRUCTIONS ALL COMPONENTS Metal profile 0 mm Gripper Ceiling attachments Screws for ceiling attachements (not included) Wires Metal profile 60 mm Metal profile 00 mm Felt - Full Felt - Half Plastic rivets mm Plastic rivets Metal profile R 50 mm, 60 mm
ASSEMBLY INSTRUCTIONS REQUIRED COMPONENTS STEP - Measure the distance between the holes on top of the metal profile and mark the ceiling. That is where the ceiling attachements will be placed. Screw the ceiling attachements in the correct position (a), then screw in the grippers (b). a b Metal profile, 0mm - 00mm Gripper Ceiling attachment Wire Insert the wire in the hole on the top side of the metal profile (a) then insert the end of the wire into the bottom tip of the gripper and pull it out through the side hole (b). To release the wire push on the bottom tip. Adjust the height of the metal profile pulling on the wires until it s hanging at about 60 cm from the floor. Screws for ceiling attachement a b 60 cm FLOOR
ASSEMBLY INSTRUCTIONS REQUIRED COMPONENTS STEP 5-8 5 Start with the top left corner: position the two full pieces as shown in the picture (piece goes under piece ) and attach them to the metal profile using two mm plastic rivets. Repeat on opposite corner. 6 Continue assembling the top row adding a full piece () and a half piece (). Place piece under piece and piece on top of piece. Attach the felt parts to the metal profile using the mm rivets, as in step 5. Metal profile, 0mm - 00mm Felt - Full Felt - Half 7 Repeat step 6 for the entire top row: piece always goes under piece and piece always on top. 8 Once the top row is complete, start with the middle rows. Place the new full piece () at the bottom. The other pieces should follow in the shown order. Use the rivets. Plastic rivet mm Plastic rivet
ASSEMBLY INSTRUCTIONS REQUIRED COMPONENTS STEP 9- If you placed the pieces in the correct order the meeting point should look like the picture on the left. The right image shows a common mistake. 9 0 Continue adding the full pieces using the same technique. The next row will start with a half piece. Felt - Full Felt - Half Plastic rivet If the ending of your Scale screen looks like picture A, follow steps and ; if it looks like picture B follow steps and. A B
ASSEMBLY INSTRUCTIONS REQUIRED COMPONENTS STEP 9- For the bottom row use the half pieces, always placing them at the bottom, as shown in the picture. Use the same process until the bottom row is complete. Felt - Full Felt - Half Plastic rivet For the bottom row use the half pieces, always placing them at the bottom, as shown in the picture. Use the same process until the bottom row is complete.
MONTERINGSANVISNING ALLA KOMPONENTER Metallprofil 0 mm Vajergrepp Takfäste Skruv för takfäste (ingår ej) Vajer Metallprofil 60 mm Metallprofil 00 mm Filt - Hel Filt - Halv Plastsnäppen mm Plastsnäppen Metallprofil R 50 mm, 60 mm
MONTERINGSANVISNING KOMPONENTER STEG - Mät avståndet mellan hålen på ovansidan av metalprofilen och markera i taket var takfästerna ska sitta. Använd x skruv och fäst takfästena på markerad plats (a), skruva därefter fast vajergreppen (b). a b Metallprofil, 0mm - 0 Vajergrepp Takfäste Vajer För in vajern i hålet på metalprofilen (a), för sedan in vajerns ände i vajergreppet och dra igenom vajern (b). För att lossa på vajern trycks toppen in samtidigt som man drar i vajern. Ändra metallprofilens höjd genom att dra i vajrarna tills den hänger ca 60 cm från golvet. Skruvar för takfäste a b 60 cm GOLV
MONTERINGSANVISNING KOMPONENTER STEG 5-8 5 Börja med hörnet uppe till vänster: placera två halvar som bilden visar (halv hamnar under halv ) och fäste dessa i metallprofilen med x plastsnäppen ( mm). Upprepa dessa steg för det högra hörnet. 6 Fortsätt med den första raden genom att fästa en hel bit () och en halv bit (). Placera bit under bit och bit ovanpå bit. Fäst filtbitarna i metallprofilen med plastsnäppen (mm) som i steg 5. Metallprofil, 0mm - 00mm Filt - Hel Filt - Halv 7 Upprepa steg 6 tills den övre raden är komplett: bit ska ALLTID placeras under bit och bit ska ALLTID placeras överst. 8 När den översta raden är komplett, börja med raderna i mitten. Placera hel biten bakom bitar, och. Placera bitar i den ordning som bilden visar. Använd plastsnäppen ( mm) för att fästa dessa med. Plastnäppen mm Plastnäppen
MONTERINGSANVISNING KOMPONENTER STEG 9- Om du placerat filtbitarna i rätt ordning kommer de i mötet se ut som på bilden till vänster. Bilden till höger visar ett vanligt misstag. 9 0 Fortsätt lägga till filtrutor med samma tillvägagångssätt som steg 8. Nästa rad kommer börja med en filt halva. Filt - Hel Filt - Halv Plastnäppen Om avslutet på din Scale vägg ska se ut som bild A, följ steg och ; om det ska se ut som bild B följ steg och. A B
MONTERINGSANVISNING KOMPONENTER STEG 9 - Använd filthalvor till den nedersta raden, den första filt halvan placeras bakom de övriga, som bilden visar. Följa samma mönster som i steg och fortsätt tills raden är klar. Filt - Hel Filt - Halv Plastnäppen Använd filthalvor till den nedersta raden, den första filt halvan placeras bakom de övriga, som bilden visar. Följa samma mönster som i steg och fortsätt tills raden är klar.