CMR 26/CMR 45. Installatörshandbok. Installer manual. Installateurhandbuch IHB 1240-3 031980



Relevanta dokument
CMR 26/CMR 45. Installatörshandbok. Installer manual. Installateurhandbuch IHB

Tariff Kit. Installatörshandbok Tariff Kit för NIBE F1330 LEK. Installer manual Tariff Kit for NIBE F1330

Installatörshandbok Överskåp. Installer manual Top cabinet. Installateurhandbuch Oberschrank. Asentajan kasikirja Yläkaappi IHB SE LEK

NIBE Uplink - Uppgradering

CTC Rumsdisplay CTC Roomdisplay Installations- och skötselanvisning. Installation and maintenance instructions

NIBE Uplink IHB

Beijer Electronics AB 2000, MA00336A,

Support Manual HoistLocatel Electronic Locks

2.1 Installation of driver using Internet Installation of driver from disk... 3

F1220, F1230, F1120, F1130

WALLMEK i Kungälv AB Special tools for auto repairs

F1220, F1230, F1120, F1130

InstalationGuide. English. MODEL:150NHighGain/30NMiniUSBAdapter

Quick Start. English Svenska. Moca

Quick Start Guide Snabbguide

INSTALLATION INSTRUCTIONS

Får endast utföras av behörig personal. May only be carried out by authorized electrician

WALLMEK i Kungälv AB Special tools for auto repairs

SERVICEINSTRUKTION Tider. SERVICE INSTRUCTION Times. Zeiten SIT SE/GB/DE M10401 FIGHTER 2005/2010

SERVICEINSTRUKTION Värmeproduktion. SERVICE INSTRUCTION Heat production. Wärmeerzeugung SIT SE/GB/DE M10383 FIGHTER 1320

Boiler with heatpump / Värmepumpsberedare

Ersättning styrkort GOLD, stl 1-3, Version 1-3/ Replacement control circuit board GOLD, sizes 1-3, Version 1-3

HANDPUMP H-11 DIRECTIONS FOR USE BRUKSANVISNING GEBRAUCHANWEISUNG

SOLAR 41. Installatörshandbok SOLAR 41. Installer manual SOLAR 41. Installateurhandbuch SOLAR 41 IHB LEK

Quick Start. English Svenska PRIMACY. Printing settings and winsign

MODBUS 40 IHB LEK

1. Unpack content of zip-file to temporary folder and double click Setup

Optioner Options Optionen

Product configurations Produire configuration Produkt konfigurationen Producto configuraciones Produkt konfigurationerna

Installation av F13 Bråvalla

THERMOMATIC 125 User and installation instructions

SOLAR 40. Installatörshansbok SOLAR 40 för NIBE F1145. Installer manual SOLAR 40 for NIBE F1145. Installateurhandbuch SOLAR 40 für NIBE F1145

WALLMEK i Kungälv AB Special tools for auto repairs

Anvisning för Guide for

Manual. SE Control Omni Dockningsstation GB Control Omni Docking station DE Control Omni Dockstation

METROSAVER MB F & F-PC

Metallmaßstäbe RL. Inhaltsverzeichnis


DEH 40/DEH 41. Installatörshandbok. Installer manual. Installateurhandbuch IHB LEK

Instruction Manual. Svenska, English. Power Bank. Model: PRBN


DEH40/41. Installatörshandbok DEH40/41. Installer manual DEH40/41. Installateurhandbuch DEH40/41 IHB LEK

Windlass Control Panel v1.0.1

PCS 44. Installatörshansbok Passiv kyla för NIBE F1145, F1245. Installer manual Passive cooling for NIBE F1145, F1245

EXP 12 MAV EXP 12 MONTERINGSANVISNING EXPANSIONSKORT 12 TILL FIGHTER 1320/1330


Logik für Informatiker

FORTA M315. Installation. 218 mm.

Dockningssats DEW 40 IHB

Quick Start Guide. To switch the TV on. cable to connect the two units together. To select the TV broadcasts. To HDMI connection on.

ARC 32. Tvättställsblandare/Basin Mixer. inr.se

GOLD SD Med styrenhet/with control unit. Fläkt/ Fan. Utan filter/ Without filter. Fläkt/Fan. Fläkt/ Fan. Med filter/ With filter.

Installationsguide. EG200 Multi WAN Residential Gateway. v

Monteringsanvisning Nödutrymningsbeslag ASSA 179E

This manual should be saved! EcoFlush Manual

81152 TRANSFER CASE SHIFT HANDLE

Technical description with installation and maintenance instructions

manual Powerbank 3X Solar Item: Linocell

SVENSKA. Bottensugkontakt Art.nr 12673

Installationsguide. DG200 Multi WAN Residential Gateway V

4.2 Konstantes Fördervolumen Doppelpume

Lösenordsportalen Hosted by UNIT4 For instructions in English, see further down in this document

SOLAR 42. Installatörshandbok SOLAR 42 för NIBE F1145. Installer manual SOLAR 42 for NIBE F1145. Installateurhandbuch SOLAR 42 für NIBE F1145

This manual should be saved! EcoFlush Manual. Wostman 2018:2

RE 10 MAV RE 10 MONTERINGSANVISNING RUMSENHET RE 10 TILL FIGHTER 1135/1235/1250/VVM 300/SMO 10

INKOPPLINGSANVISNING ELTRYCKSLÅS WIRING DIAGRAM SOLENOID LOCK

säkerhetsutrustning / SAFETY EQUIPMENT

GOLD SD Fläkt 2/ Fan 2. Fläkt 1/ Fan 1. Fläkt/ Fan. Utan filter/ Without filter. Fläkt 1/ Fan 1. Fläkt 2/ Fan 2. Med filter/ With filter Filter

Isolda Purchase - EDI

VASSVIK FIXED STAND SE / ENG

manual Bluetooth car handsfree Road talk Item: Linocell

Vanliga frågor om Duocom (för installatör eller reparatör) GB Frequently asked questions about Duocom (for installer or repairman)

SCdefault. 9-5 Monteringsanvisning

Digital Personvåg MANUAL H

PPV-Serie. DIN Axialkolben Verstellpumpe für LKW Nebenabtrieb mit Load Sensing-Regler. Erstinbetriebnahme: Saugstutzen muß separat bestellt werden

IPCorder KNR-412 Installation manual

BBT057/ BBC057 BBCD057/ BBT057-NL HOLDEN COLORADO 9/2016+ HOLDEN TRAILBLAZER WD & 4WD Models

ECS 40. Installatörshansbok Extra Klimatsystem för NIBE F1145, F1245. Installer manual Extra climate system for NIBE F1145, F1245

P650 - Takscreen. Installationsguide EN

MCP-16RC, Air Purification

PRESS FÄLLKONSTRUKTION FOLDING INSTRUCTIONS

manual Facial spa Art nr: Rubicson

ASSEMBLY INSTRUCTIONS SCALE - SYSTEM

BPS BPS Lönsam flödesteknik Rewarding Flow Technology Vorteilhafte Regel- und Absperrtechnik

Installation Instructions

English Svenska. Installation. Guide. XG6846 Broadband Switch

Digital Personvåg MANUAL H

Veranda. DE Installationshandbuch V17/16

PRESS FÄLLKONSTRUKTION FOLDING INSTRUCTIONS

Information technology Open Document Format for Office Applications (OpenDocument) v1.0 (ISO/IEC 26300:2006, IDT) SWEDISH STANDARDS INSTITUTE

2.45GHz CF Card Reader User Manual. Version /09/15

Plain A262. För T16 (T5) lysrör. Innehåll. Monteringsanvisning. A. Instruktion för rampmontering

Användarhandbok NIBE Uplink

SAFETY PRECAUTIONS SPECIFICATIONS

D-285 r0. Installationsanvisning för ServiceTool

Diskant Yta eller Vikelfäste montering Mount

BAU 10. Installatörshandbok Konsolmontering SE. Installer manual Bracketsassembly GB. Installateurhandbuch Konsolenmontage DE

GOLD SD Med styrenhet/with control unit. Fläkt 1A/B/ Fan 1A/B. Fläkt 2A/B/ Fan 2A/B. Fläkt/ Fan. Utan filter/ Without filter

Z-LYFTEN PRODUKTION AB MONTERINGSANVISNING INSTALLATION INSTRUCTIONS

Montageanvisning Airway system 1000/1500 Assembly instruction Airway system 1000/1500

Transkript:

CMR 2/CMR 4 SE GB DE Installatörshandbok Installer manual Installateurhandbuch IHB 1240-3 03190

Svenska SE Allmänt CMR 2/CMR 4 är en utbyteskylmodul för NIBE F112/114/122/124. Alla kompressorstorlekar är inte utbytbara mot varandra. Vid byte från en mindre storlek till en större ska följande beaktas: borrhålets/kollektorslingans dimensionering värmesystemets storlek varmvattenberedarens storlek husets och/eller värmepumpens avsäkring matningskabeln area rörens dimension (internt i värmepumpen samt klimatsystemet) Kontrollera även att utbyteskylmodulen har samma matningsspänning som originalkylmodulen. Innehåll Antal 1st st 1st 1st 1st Beskrivning Kylmodul O-ringar Planpackning Dräneringspip USB-minne med programvara OBS! Elektrisk installation och ledningsdragning ska utföras enligt gällande bestämmelser. Tänk på Om den nya kylmodulen är av samma märke och modell som originalkylmodulen behöver du inte uppdatera programvaran eller ändra kylmodulen i displayen. Om den nya kylmodulen inte är av samma märke och/eller modell som originalkylmodulen kan även cirkulationspumparna behöva ändras i displayen. Medlevererat USB-minne med program måste anslutas för att hantera uppdateringen av programvaran. Se respektive värmepumps installationshandbok för beskrivning och hantering av menyer och menysystem. Dokumenten finns att ladda hem på www.nibe.se. För att motverka framtida driftstörningar är det viktigt att rätt kylmodul är vald i meny 7.4 - "serienummer". Alla de inställningar du har gjort i värmepumpen finns kvar efter uppdateringen. Om något går fel vid uppdateringen kan du alltid återgå till den tidigare installerade programvaran (se sida ). 3

SE Programvara Om utbyteskyldelen inte är av samma storlek som originalkylmodulen behöver värmepumpens programvara uppdateras. Kontrollera aktuell kompressorstorlek Gå in i meny 3.1 - "serviceinfo" för att kontrollera aktuell storlek på kompressorn. serviceinfo 3.1 Ändra i displayen OBS! Om anläggningen för närvarande har en programvaruversion lägre än v3000 måste du först installera UPGRADE_v3000.nibe innan du kan installera en ny programvara. Om inte anläggningen automatiskt föreslår programvara med versionsnummer 3000 i menyn "uppdatera programvaran", navigera till "välj annan fil", tryck OK och välj mjukvaran UPGRADE_v3000.nibe. Välj därefter "starta uppdatering". När UPGRADE_v3000.nibe har installerats (stapeln har nått 100% och anläggningen startat om) kommer den automatiskt att starta installationen av den andra programvaran som ligger på USB-minnet. 1. Anslut det medlevererade USB-minnet i värmepumpens displayenhet. Kontrollera aktuell cirkulationspump Gå in i meny 3.1 - "serviceinfo" för att kontrollera aktuell modell av cirkulationspump. 2. Gå in i meny 7.1 - "uppdatera programvaran" och följ anvisningarna i displayen. 4

SE 3. Gå in i meny 7.4 - "serienummer". Återställning av tidigare programvaruversion Om uppdateringen skulle avbrytas innan den är klar (t.ex. vid strömavbrott) kan programvaran återställas till tidigare version. Därefter kan du återigen påbörja installationen av den nya programvaran. Minnet i värmepumpen innehåller alltid två versioner av programvaran: den som används just nu samt föregående installerad programvara. För att växla mellan dessa versioner: 1. Ställ strömställaren i läge ( ). 4. Välj aktuell cirkulationspump.. När du bekräftat valet av ny cirkulationspump tillkommer en stjärna efter serienumret.. Kontrollera i meny 3.1 - "serviceinfo" att rätt cirkulationspump är vald. 2. Håll inne OK-knappen på displayenheten och ställ samtidigt strömställaren i läge (). 3. Släpp OK-knappen när den gröna lampan tänds (tar ca. 10 sekunder). Nu har den föregående programvaran blivit aktiverad.

SE Byte av kylmodul F112/114 OBS! Stäng av värmepumpen och vrid av strömmen på säkerhetsbrytaren. Lossa kontakterna från grundkortet (AA2) med hjälp av skruvmejsel. TÄNK PÅ! Ta bort frontluckan enligt beskrivning i värmepumpens installatörshandbok. 1 Stäng avstängningsventilerna (QM32), (QM33) och (QM34). Tappa ur kylmodulen enligt anvisningarna i värmepumpens installatörshandbok. Lossa kontakterna (A) och (B) från undersidan av grundkortslådan. 7 Lossa kontakten (C) från elpatronskortet (AA1) med hjälp av skruvmejsel. Lossa kontakten (D) från skarvkortet (AA100). 2 Dra av låsblecken. 9 Dra försiktigt ut kylmodulen. 3 Lossa röranslutningen vid rörkopplingen (WP4). 4 Lossa de två skruvarna.

SE TIPS! Kylmodulen monteras i omvänd ordning. OBS! Vid återmonteringen ska medlevererade O-ringar samt planpackning ersätta befintliga vid anslutningarna till värmepumpen (se bild). Montering av dräneringspip Montera den medlevererade dräneringspipen i det avsedda hålet på kylmodulen (se bild nedan). 7

SE Byte av kylmodul F122/124 OBS! Stäng av värmepumpen och vrid av strömmen på säkerhetsbrytaren. Lossa kontakterna från grundkortet (AA2) med hjälp av skruvmejsel. TÄNK PÅ! Ta bort frontluckan enligt beskrivning i värmepumpens installatörshandbok. 1 Stäng avstängningsventilerna (QM32), (QM33) och (QM34). Tappa ur kylmodulen enligt anvisningarna i värmepumpens installatörshandbok. Lossa kontakterna (A) och (B) från undersidan av grundkortslådan. 7 Lossa kontakten (C) från elpatronskortet (AA1) med hjälp av skruvmejsel. 2 Dra av låsblecken. 9 Lossa kontakten (D) från skarvkortet (AA100). Dra försiktigt ut kylmodulen. 3 Lossa röranslutningen vid rörkopplingen (WP4). 4 Lossa de två skruvarna.

SE TIPS! Kylmodulen monteras i omvänd ordning. OBS! Vid återmonteringen ska medlevererade O-ringar samt planpackning ersätta befintliga vid anslutningarna till värmepumpen (se bild). Montering av dräneringspip Montera den medlevererade dräneringspipen i det avsedda hålet på kylmodulen (se bild nedan). 9

SE Tekniska data Värmepump Effekt (w) Art nr Kylmodul Vikt (kg) F112/F122 3x400 V 07 114 CMR 2-10 07 11 CMR 2-112 07 11 CMR 2-120 11 07 117 CMR 2-11 130 F114/F124 3x400 V 07 14 CMR 4-110 07 11 CMR 4-11 07 119 CMR 4-12 10 07 120 CMR 4-10 130 12 07 121 CMR 4-12 13 1 07 122 CMR 4-1 14 17 07 123 CMR 4-17 1 F114/F124 3x230 V 07 12 CMR 4-3x230V 11 07 13 CMR 4-3x230V 12 10 07 14 CMR 4-10 3x230V 130 12 07 1 CMR 4-12 3x230V 13 1 07 1 CMR 4-1 3x230V 14 17 07 17 CMR 4-17 3x230V 1 F114/F124 1x230 V 07 14 CMR 4-1x230V 110 07 19 CMR 4-1x230V 12 10 07 190 CMR 4-12 1x230V 130 10

English GB General CMR 2/CMR 4 is a replacement cooling module for NIBE F112/114/122/124. All compressor sizes are not interchangeable. When replacing from a smaller size to a larger size, observe the following: the bore hole's/collector coil's dimensioning the size of the heating system size of the water heater the fuse rating of the house and /or heat pump area of the supply cable dimension of the pipes (inside the heat pump and climate system) Contents Quantity Description 1x Cooling module x O-rings 1x Flat gasket 1x Drainage pipe 1x USB memory with software Also check that the replacement cooling module has the same supply voltage as the original cooling module. NOTE Electrical installation and wiring must be carried out in accordance with the stipulations in force. Remember If the new cooling module is the same make and model as the original cooling module, you do not need to update the software or change the cooling module in the display. If the new cooling module is not the same make and/or model as the original cooling module, the circulation pumps may also need to be changed in the display. The supplied USB memory with program must be connected to manage the software update. See the relevant heat pump's installation manual for descriptions and how to navigate menus and the menu system. Documentation can be downloaded from www.nibe.se. To prevent future malfunctions it is important that the correct cooling module is selected in menu 7.4 - "serial number". All the settings that you have made in the heat pump remain after the update. If anything goes wrong during the update you can always return to the previously installed software (see page 13). 11

GB Software If the replacement cooling section is not the same size as the original cooling module, the heat pump software needs updating. Check the current compressor size Enter menu 3.1 - "service info" to check current compressor size. service info 3.1 Change in the display NOTE If the current version of the firmware in the system is lower than 3000 you must first install UPGRADE_v3000.nibe before you can install a new firmware file. If the system doesn't automatically propose the firmware with version number 3000 in the menu "update firmware", navigate to "choose another file", press OK and choose the firmware UPGRADE_v3000.nibe. Thereafter choose "start updating". When UPGRADE_v3000.nibe has been installed (the progress bar has reached 100% and the system has restarted) it will automatically start the installation of the second firmware file on the USB stick. 1. Insert the supplied USB memory into the heat pump's display unit. Check the current circulation pump Enter menu 3.1 - "service info" to check current circulation pump model. 2. Enter menu 7.1 - "update firmware" and follow the instructions in the display. 12

GB 3. Enter menu 7.4 - "serial number". Resetting previous software version If the update is interrupted before it is complete (for example power cut etc.) the software can be reset to the previous version. You can then restart the installation of the new software. The memory in heat pump always contains two versions of the software: one that is used at present and the previously installed software. To shift between these versions: 1. Set the switch to mode ( ). 4. Check the current circulation pump.. Once you have confirmed the new circulation pump selection a star appears after the serial number.. Check in menu 3.1 - "service info" that the correct circulation pump has been selected. 2. Keep the OK button held in on the display unit and at the same time set the switch to ( ). 3. Release the OK button when the green lamp illuminates (takes approx 10 seconds). The previous software has now been activated. 13

GB Replacing cooling module F112/114 Remove the connections from the base card (AA2) using a screwdriver. NOTE Shut off the heat pump and turn off the current on the safety breaker. Caution Remove the front door according to the description in the heat pump's installer's manual. 1 Close the shut-off valves (QM32), (QM33) and (QM34). Drain the cooling module according to the instructions in the heat pump's installer's manual. 7 Disconnect the connectors (A) and (B) from the underside of the base card cabinet. Disconnect the connector (C) from the immersion heater circuit board (AA1) using a screwdriver. Disconnect the connector (D) from the joint circuit board (AA100). 9 Carefully pull out the cooling module. 2 Pull off the lock catches. 3 4 Disconnect the pipe connection at the pipe coupling (WP4). Remove the two screws. 14

GB TIP The cooling module is installed in reverse order. NOTE At reinstallation, the supplied O-rings and flat gasket must replace the existing ones at the connections to the heat pump (see image). Installing the drainage pipe Install the supplied drainage pipe in the intended hole on the cooling module (see image below). 1

GB Replacing cooling module F122/124 Remove the connections from the base card (AA2) using a screwdriver. NOTE Shut off the heat pump and turn off the current on the safety breaker. Caution Remove the front door according to the description in the heat pump's installer's manual. 1 Close the shut-off valves (QM32), (QM33) and (QM34). Drain the cooling module according to the instructions in the heat pump's installer's manual. Disconnect the connectors (A) and (B) from the underside of the base card cabinet. 7 Disconnect the connector (C) from the immersion heater circuit board (AA1) using a screwdriver. Disconnect the connector (D) from the joint circuit board (AA100). 2 Pull off the lock catches. 9 Carefully pull out the cooling module. 3 Disconnect the pipe connection at the pipe coupling (WP4). 4 Remove the two screws. 1

GB TIP The cooling module is installed in reverse order. NOTE At reinstallation, the supplied O-rings and flat gasket must replace the existing ones at the connections to the heat pump (see image). Installing the drainage pipe Install the supplied drainage pipe in the intended hole on the cooling module (see image below). 17

GB Technical specifications Heat pump Power (w) Part No. Cooling module Weight (kg) F112/F122 3x400 V 07 114 CMR 2-10 07 11 CMR 2-112 07 11 CMR 2-120 11 07 117 CMR 2-11 130 F114/F124 3x400 V 07 14 CMR 4-110 07 11 CMR 4-11 07 119 CMR 4-12 10 07 120 CMR 4-10 130 12 07 121 CMR 4-12 13 1 07 122 CMR 4-1 14 17 07 123 CMR 4-17 1 F114/F124 3x230 V 07 12 CMR 4-3x230V 11 07 13 CMR 4-3x230V 12 10 07 14 CMR 4-10 3x230V 130 12 07 1 CMR 4-12 3x230V 13 1 07 1 CMR 4-1 3x230V 14 17 07 17 CMR 4-17 3x230V 1 F114/F124 1x230 V 07 14 CMR 4-1x230V 110 07 19 CMR 4-1x230V 12 10 07 190 CMR 4-12 1x230V 130 1

Deutsch DE Allgemeines CMR 2/CMR 4 ist ein Austauschartikel für NIBE F112/114/122/124. Nicht alle Verdichtergrößen sind gegeneinander austauschbar. Beim Austausch von einer kleineren zu einer größeren Einheit ist Folgendes zu beachten: Dimensionierung der Wärmequelle Größe des Heizsystems Größe des Brauchwasserspeichers Elektrische Absicherung des Hauses und/oder der Wärmepumpe Querschnitt des Stromversorgungskabels Abmessung der Rohre (innerhalb der Wärmepumpe sowie im Klimatisierungssystem) Überprüfen Sie auch, dass das Austauschkältemodul die gleiche Versorgungsspannung benötigt, wie das Originalkältemodul. Inhalt Anzahl 1 St. St. 1 St. 1 St. 1 St. Beschreibung Kältemodul O-Ringe Flachdichtung Entleerungstülle USB-Stick mit Software HINWEIS! Bei der elektrischen Installation und beim Verlegen der Leitungen sind die geltenden Vorschriften zu berücksichtigen. Zur Beachtung Wenn das neue Kältemodul von der gleichen Serie und vom gleichen Typ wie das Originalkältemodul ist, müssen Sie die Software nicht aktualisieren und das Kältemodul im Display nicht ändern. Wenn das neue Kältemodul nicht von der gleichen Serie und/oder Typ wie das Originalkältemodul ist, müssen eventuell auch die Umwälzpumpen im Display geändert werden. Der mitgelieferte USB-Stick muss angeschlossen werden und das Programm enthalten, um die Aktualisierung der Software vornehmen zu können. Beschreibung und Bedienungshinweise für die Menüs und das Menüsystem gehen aus dem Montagehandbuch für das jeweilige Produkt hervor. Die Dokumente stehen unter www.nibe.se zum Download bereit. Um spätere Betriebsstörungen zu vermeiden, muss unbedingt das korrekte Kältemodul eingestellt werden im Menü 7.4 - "Seriennummer". Alle in der Wärmepumpe vorgenommenen Einstellungen bleiben bei der Aktualisierung erhalten. Wenn bei der Aktualisierung ein Fehler auftritt, lässt sich die vorherige Version stets wiederherstellen (sieheseite 21). 19

DE Software Wenn das Austauschkältemodul nicht die gleiche Größe hat wie das Originalkältemodul, muss die Software der Wärmepumpe aktualisiert werden. Ermitteln der aktuellen Verdichtergröße Gehen Sie in Menü 3.1 - "Serviceinfo", um die aktuelle Größe des Verdichters zu ermitteln. Serviceinfo 3.1 Änderung im Display HINWEIS! Wenn die Anlage zurzeit eine frühere Softwareversion als 3000 hat, müssen Sie zuerst UPGRA- DE_v3000.nibe installieren, bevor Sie eine neue Softwareversion installieren können. Wenn die Anlage nicht automatisch die Softwareversion 3000 im Menü Softwareupdate vorschlägt, wählen Sie andere Datei, bestätigen mit OK und wählen Sie Software UPGRADE_v3000.nibe. Wählen Sie danach Update starten. Wenn UPGRADE_v3000.nibe installiert ist (Der Stapel hat 100% erreicht und die Anlage hat neu gestartet.) wird automatisch die Installation der anderen Software auf dem USB-Stick gestartet. 1. Verbinden Sie den mitgelieferten USB-Stick mit dem Bedienfeld der Wärmpumpe. Ermitteln der aktuellen Umwälzpumpe Gehen Sie in Menü 3.1 - "Serviceinfo", um das aktuell eingestellte Modell der Umwälzpumpe zu ermitteln. 2. Rufen Sie Menü 7.1 - "Softwareupdate" auf und befolgen Sie die Anweisungen auf dem Display. 20

DE 3. Gehen Sie in Menü 7.4 - "Seriennummer". 4. Wählen Sie die aktuelle Umwälzpumpe.. Wenn Sie die Wahl der neuen Umwälzpumpe bestätigt haben, erscheint hinter der Seriennummer ein Stern.. Überprüfen Sie im Menü 3.1 -"Serviceinfo", dass die korrekte Umwälzpumpe eingestellt ist. Vorherige Softwareversion wiederherstellen Wenn die Aktualisierung abgebrochen werden sollte, bevor sie abgeschlossen ist (z. B. bei einer Stromunterbrechung), kann eine frühere Version der Software wiederhergestellt werden. Anschließend können Sie wieder mit der Installation der neuen Software beginnen. Der Wärmepumpenspeicher enthält stets zwei Softwareversionen: die aktuell verwendete und die zuvor installierte. So wechseln Sie zwischen den beiden Versionen: 1. Bringen Sie den Schalter in die Stellung ( ). 2. Halten Sie die OK-Taste am Bedienfeld gedrückt, während Sie den Schalter in die Stellung () bringen. 3. Lassen Sie die OK-Taste los, wenn die grüne Lampe aufleuchtet (dies dauert ca. 10 s). Somit wurde die vorherige Softwareversion wiederhergestellt. 21

DE Austausch des Kältemoduls F112/114 Lösen Sie die Anschlüsse mithilfe eines Schraubendrehers von der Grundkarte (AA2). HINWEIS! Stellen Sie die Wärmepumpe aus und trennen Sie die Stromversorgung per Sicherheitsschalter. ACHTUNG! Entfernen Sie die Frontabdeckung gemäß der Beschreibung im Installateurhandbuch der Wärmepumpe. 1 Schließen Sie die Absperrventile (QM32), (QM33) und (QM34). Entleeren Sie das Kältemodul gemäß der Anweisungen im Installateurhandbuch der Wärmepumpe. 7 Lösen Sie die Anschlüsse (A) und (B) von der Unterseite des Grundkartengehäuses. Lösen Sie den Anschluss (C) mithilfe eines Schraubendrehers von der Elektroheizpatronenkarte (AA1). Lösen Sie den Anschluss (D) von der Verbindungskarte (AA100). 9 Ziehen Sie das Kältemodul vorsichtig heraus. 2 Ziehen Sie das Sperrblech ab. 3 4 Lösen Sie den Rohranschluss an der Rohrkupplung (WP4). Lösen Sie die beiden Schrauben. 22

DE TIP! Führen Sie die Montage des Kältemoduls in umgekehrter Reihenfolge aus. HINWEIS! Bei der erneuten Montage sind die vorhandenen O-Ringe samt Flachdichtung an den Wärmepumpenanschlüssen durch die beiliegenden O-Ringe zu ersetzen (siehe Abb.). Montage der Entleerungstülle Montieren Sie die mitgelieferte Entleerungstülle im dafür vorgesehenen Loch am Kältemodul (siehe Abbildung unten). 23

DE Austausch des Kältemoduls F122/124 Lösen Sie die Anschlüsse mithilfe eines Schraubendrehers von der Grundkarte (AA2). HINWEIS! Stellen Sie die Wärmepumpe aus und trennen Sie die Stromversorgung per Sicherheitsschalter. ACHTUNG! Entfernen Sie die Frontabdeckung gemäß der Beschreibung im Installateurhandbuch der Wärmepumpe. 1 Schließen Sie die Absperrventile (QM32), (QM33) und (QM34). Entleeren Sie das Kältemodul gemäß der Anweisungen im Installateurhandbuch der Wärmepumpe. Lösen Sie die Anschlüsse (A) und (B) von der Unterseite des Grundkartengehäuses. 7 Lösen Sie den Anschluss (C) mithilfe eines Schraubendrehers von der Elektroheizpatronenkarte (AA1). Lösen Sie den Anschluss (D) von der Verbindungskarte (AA100). 9 Ziehen Sie das Kältemodul vorsichtig heraus. 2 Ziehen Sie das Sperrblech ab. 3 Lösen Sie den Rohranschluss an der Rohrkupplung (WP4). 4 Lösen Sie die beiden Schrauben. 24

DE TIP! Führen Sie die Montage des Kältemoduls in umgekehrter Reihenfolge aus. HINWEIS! Bei der erneuten Montage sind die vorhandenen O-Ringe samt Flachdichtung an den Wärmepumpenanschlüssen durch die beiliegenden O-Ringe zu ersetzen (siehe Abb.). Montage der Entleerungstülle Montieren Sie die mitgelieferte Entleerungstülle im dafür vorgesehenen Loch am Kältemodul (siehe Abbildung unten). 2

DE Technische Daten Wärmepumpe Leistung (W) Art.nr. Kältemodul Gewicht (kg) F112/F122 3x400 V 07 114 CMR 2-10 07 11 CMR 2-112 07 11 CMR 2-120 11 07 117 CMR 2-11 130 F114/F124 3x400 V 07 14 CMR 4-110 07 11 CMR 4-11 07 119 CMR 4-12 10 07 120 CMR 4-10 130 12 07 121 CMR 4-12 13 1 07 122 CMR 4-1 14 17 07 123 CMR 4-17 1 F114/F124 3x230 V 07 12 CMR 4-3x230V 11 07 13 CMR 4-3x230V 12 10 07 14 CMR 4-10 3x230V 130 12 07 1 CMR 4-12 3x230V 13 1 07 1 CMR 4-1 3x230V 14 17 07 17 CMR 4-17 3x230V 1 F114/F124 1x230 V 07 14 CMR 4-1x230V 110 07 19 CMR 4-1x230V 12 10 07 190 CMR 4-12 1x230V 130 2

NIBE AB Sweden Hannabadsvägen Box 14 SE-2 21 Markaryd Phone +4 433 73 000 Telefax +4 433 73 190 info@nibe.se www.nibe.se 03190