GB Instruction for use SE Bruksanvisning! PRSJ/PRSE-11-2014 POWERTEX Rigging Screw model PRSJ/PRSE 1
POWERTEX Closed Body Rigging Screw Instruction for use (GB) (Original instructions) Read through these user instructions carefully before using the closed body rigging screw. Improper operation may lead to hazardous situations! 1. EC Declaration of conformance is required and report of thorough excamination. 2. Before use each rigging screw should be inspected to ensure that: all markings in the product are readable and in compliance with the relevant documentation. the components are assembled in correct way. body and end terminals shall not be distorted or unduly worn. Body and terminals are free from nicks, cracks, grooves and corrosion. If there is any doubt with regards to the above criteria being met, the rigging screw should not be used. 3. Before putting load on it is important to ensure that the terminals are safely locked. All threads in the ends of the body must be fully engaged with the terminal threads, and safety locked with the stop nuts. 4. Turnbuckles should be fitted to the load in a manner that allows the turnbuckle to take the load in a true line along its centerline to avoid much bending stresses which will reduce the load capacity of the turnbuckle. To avoid eccentric loading of the terminal it is recommended to distribute the load as for as possible over the total length of the pin or to use loose spacers. 5. Temperature range: -20 C - +200 C. 6. Never modify the fittings eg. to reduce the inside with of a terminals by pressing on the side eyes or welding washers / spacers to the inside of the eyes such action makes the declaration of conformance invalid. 7. For lifting! Do not length adjust under load. Threads WLL 5:1 T Load limit M6-0,20 M8-0,32 M10 0,5 - M12 0,7 - M16 1,2 - M20 1,5 - M22 2,2 - M24 3,2 - M33 4,8 - M39 6,0 - M45 8,5 - M52 11,0 M56 15,0 M64 25,0 WARNING Failure to follow the regulations of this mounting instruction may cause serious consequences such as risk of injury. Read and understand these instructions before use. Disclaimer CERTEX GROUP reserves the right to modify product design, materials, specifications or instructions without prior notice and without obligation to others. Declaration of conformity CERTEX Wenner Gren Center Sveavägen 166 15fl SE-113 46 Stockholm hereby declares that Powertex Closed Rigging Screw as described above has been manufactured in conformity with EC Machinery Directive 2006/42/EC and amendments. If the product is modified in any way, or if it is combined with a non-compatible product/component, CERTEX Group take no responsibility for the consequences in regard to the safety of the product. 2
POWERTEX Vantskruv Bruksanvisning (SE) (Översättning av bruksanvisning i original) Läs dessa anvisningar noga innan du använder vantskruven. Felaktigt handhavande kan leda till farliga situationer! 1. Användaren är skyldig att inneha ett giltigt provcertifikat för vantskruvar som används i en lyftutrustning. 2. Innan vantskruven tas i bruk ska den inspekteras för att säkerställa att: samtliga märkningar på produkten är läsbara och överensstämmer med det relevanta provcertifikatet. komponenterna är korrekt monterade. kropp och anslutningar inte är deformerade eller slitna. kropp och anslutningar är fria från hack, sprickor, skåror och korrosion. Vid minsta tvekan om ovanstående ska vantskruven inte användas. 3. Innan belastning är det viktigt att säkerställa att anslutningar är säkert låsta. Hela gängan i kroppens ändar måste vara fyllda av anslutningarnas gängor och låsta med stoppmuttrarna. 4. Vantskruvarna ska monteras på lasten så att vantskruven belastas längs dess centrallinje för att undvika böjpåfrestningar som sänker belastningskapaciteten. För att undvika excentrisk belastning av bygeln rekommenderas att belastningen fördelas, så långs som möjligt över hela sprinten längd eller att lösa distanser används. 5. Temperaturområde: -20 C +200 C. 6. Försök aldrig minska anslutningarnas bredd genom att pressa in byglarnas sidor eller svetsa brickor/distanser på byglarnas insidor. Att göra så gör provcertifikatet ogiltigt. 7. Vid lift! Avsett för lyft! Vantskruven får inte längdjusteras i belastat tillstånd. Gänga WLL 5:1 T Belastningsgräns M6-0,20 M8-0,32 M10 0,5 - M12 0,7 - M16 1,2 - M20 1,5 - M22 2,2 - M24 3,2 - M33 4,8 - M39 6,0 - M45 8,5 - M52 11,0 M56 15,0 M64 25,0 VARNING Underlåtenhet att efterleva denna bruksanvisning kan leda till allvarliga konsekvenser såsom risk för personskador. Läs och var säker på att du förstår dessa anvisningar före användning. Friskrivningsklausul CERTEX GROUP förbehåller sig rätten att ändra produktens konstruktion, material, specifikationer eller anvisningar utan föregående meddelande och utan skyldigheter gentemot andra parter. Försäkran om överensstämmelse CERTEX Wenner Gren Center Sveavägen 166 15fl SE-113 46 Stockholm försäkrar härmed att ovan beskrivna Powertex vantskruv har tillverkats i överensstämmelse med EC maskindirektiv 2006/42/EC och ändringar. Om produkten modifieras på något sätt eller om den används tillsammans med en icke kompatibel produkt/komponent, påtar CERTEX Group sig inget ansvar för konsekvenserna med avseende på denna produkts säkerhet. 3
CERTEX Denmark Tel: +45 74 54 14 37 Fax: +45 74 54 05 62 E-mail: salg@certex.dk www.certex.dk CERTEX Sweden Tel: +46 (0) 8758 0010 Fax: +46 (0) 8758 3813 E-mail: info@certex.se www.certex.se CERTEX Norway Tel: +47 66 79 95 00 Fax: +47 66 79 95 30 E-mail: certex.oslo@certex.no www.certex.no CERTEX Finland Tel: +358 (0) 201 550 220 Fax: +358 (0) 201 550 230 E-mail: info@certex.fi www.certex.fi CERTEX UK Tel: +44 845 230 7475 Fax: +44 845 230 7476 Email: sales@certex.co.uk www.certex.co.uk CERTEX Germany Tel: +49 (0) 211 67009-0 Fax: +49 (0) 211 67009-49 E-mail: info@certex.de www.certex.de CERTEX Estonia Tel: +372 6205 136 Fax: +372 6205 146 E-mail: info@certex.ee www.certex.ee CERTEX Lithuania Tel: +370 (2) 322 297 Fax: +370 (2) 322 298 E-mail: info@certex.lt www.certex.lt CERTEX Latvia Tel: +371 761 1882 Fax: +371 6780 5072 E-mail: info@certex.lv www.certex.lv ERLING HAUG Tel: +47 73 53 97 00 Fax: +47 73 53 97 01 E-mail: firmapost@haug.no www.haug.no CERTEX Offshore Services Tel: +47 71 58 87 00 Fax: +47 71 58 87 01 E-mail: offshore@certexoffshore.no www.certexoffshore.no CERTEX Russia Tel: +7 812 335 09 65 Fax: +7 812 335 09 65 E-mail: salesstp@certex.net www.certex.net Mennens Netherlands www.mennens.nl Mennens Belgium Tel.: +32(0)3 253 23 23 Fax: +32(0)3 253 23 24 E-mail: info@mennensbelgium.be www.mennensbelgium.be 4
CERTEX Lifting KnowHow app Download The Lifting KnowHow app en from the App Store / Google play! The App has the following features: - Load charts for different types of lifting slings - Protractor for measuring sling angles - Instructions for safe use of a selection of lifting gear - Built-in gps function that finds the CERTEX office closest to your position. - And a lot more. The Lifting KnowHow is a unique knowledge transfer programme, exclusively designed by CERTEX. CertMax + The CertMax+ system is a unique leading edge certification management system which is ideal for managing a single asset or large equipment portfolio across multiple sites. Designed by CERTEX, to deliver optimum asset integrity, quality assurance and traceability, the system also improves safety and risk management levels. User Manuals You can always find the valid and updated User Manuals on the web. The manual is updated continuously and valid only in the latest version.! NB! The English version is the Original instruction. The manual is available as a download under the following link: www.certex.net/manuals Version no. 2014-11 5
www.certex.net