Köldmdieslang/ Refrigerant hose Øi Øy H 190 7,9 mm(5/16 ) 15,2 6 191,2 mm(13/32 ) 17,8 8 264 12,5 mm (1/2 ) 19,9 192 15,6 mm(5/8 ) 24,1 12 187 Tång burgaclip/ 188 Slangklippare / Hose cutter 206 208 2 219 Låsklipp/ Clip 205 207 209 218 Låsklipp hållare / Clip holder 56
Koppling hona 90 / Female 90 Gänga/Thread F H 199 5/8-18 6 6 200 3/4-16 8 8 201 7/8-14 225 7/8-14 12 224 11/16-14 12 12 Gänga/Thread F H 226 3/4-16 8 8 227 7/8-14 228 7/8-14 12 Serviceventil 90 /Service valve 90 Gänga/Thread F H 229 5/8-18 6 6 230 3/4-16 8 8 231 7/8-14 Block 90 / Blocktype 90 Gänga/Thread F H 232 3/4-16 8 8 233 7/8-14 Block serviceventil 90 / Blocktype service valve 90 Gänga/Thread F H 234 5/8-18 6 6 235 7/8-18 Rak hane / Straight male 57
Gänga/Thread F H 236 5/8-18 6 6 237 7/8-18 Koppling hane 90 / Male 90 Gänga/Thread F H 193 5/8-18 6 6 194 3/4-16 8 8 195 7/8-14 220 7/8-14 12 12 221 1 1/16-14 12 Koppling BC rak hona/ Straight female Gänga/Thread F H 241 5/8-18 6 6 242 3/4-16 8 8 243 7/8-14 Koppling hane 90 / Male 90 Gänga/Thread F H 238 5/8-18 6 6 239 3/4-16 8 8 240 7/8-14 Rak hane / Straight male Gänga/Thread F H 196 5/8-18 6 6 197 3/4-16 8 8 198 7/8-14 223 7/8-14 12 222 1 1/16-14 12 12 Koppling hona 45 / Female 45 58
Gänga/Thread F H 202 5/8-18 6 6 203 3/4-16 8 8 204 7/8-14 Koppling hane 90 / Male 90 Gänga/Thread F H 244 5/8-18 6 6 245 3/4-16 8 8 246 7/8-14 SkottgenomgångBulkhead Gänga/Thread F H 247 5/8-18 6 6 248 3/4-16 8 8 249 7/8-14 Skottgenomgång 90 / Bulkhead 90 Gänga/Thread F H 250 5/8-18 6 6 251 3/4-16 8 8 252 7/8-14 Skottgenomgång 45 /Bulkhead 45 Gänga/Thread F H 253 - - 8 254 - - Serviceventil inline / Service valve inline 59
56 Gänga/Thread F H 255 - - 6 256 - - 8 257 - - 258 - - 12 Koppling lnine/fitting inline Gänga/Thread F H 259 3/4-16 8 8 Koppling 180 hona / 80 female Gänga/Thread F H 261 3/4-16 8 8 262 7/8-14 263 7/8-14 12 Koppling rak hona serviceventil / Fitting straight female service valve 60
Monterinsanvisning /Assembly instruction Kapa slangen Kapa slangen till rätt längd med slangklipparen. Klippet måste vara rätt i förhållande till slanglängden. Cut the hose Cut the hose to proper length with the hose cutter. The cut must be made normal to the hose length. Placera två clip i klipphållaren Installera två clip i rätt storlek i cliphållaren. För att det ska gå lätt att montera ska båda clip en ha samma läge. Place the two clip s in the holder Install two proper-sized clips into the clipholder. For ease of assembly both clips should have the same orientation. Trä på cliphållaren med clip Placera klipphållaren med de två clip en på slangen. Gör det på ett sådant sätt att det minsta hålet berör änden på slangen. Slip on the clipholder with the clips. Place the clipholder with the two clips on the hose. Do it so that the side with the smallest hole touches the end of the hose. Olja kopplingen Olja in kopplingen med mycket A/C system olja. Detta görs för att minska motståndet vid monteringen. Oil the fitting Lubricate the fitting with a generous amount of the A/C system s lubricator oil. This is to lower the force of the insertion. Montera på kopplingen på slangen Trä på kopplingen på slangen. Se till att kopplingen är helt påträdd genom att kolla gapet mellan änden på slangen och kragen på kopplingen. Insert the clip fitting into the hose Insert the fitting into the hose. Ensure that the fitting is fully inserted by checking the gap between the end of the hose and the shoulder of the fitting. Stäng clip en Stäng de båda clip en med tången. Tången öppnar sig när rätt kraft har uppnåtts. Börja med clip et som är närmast änden. Close the clips Close both Clips with the clip pliers. The pliers open themselves when the right force has been reached. Start with the clip closest to the end of the hose. Färdigt! Done! 61