Produkt Brochyr IL-120 3 st. MRP-45 + Lyft fixturplatta PLE-700 Din leverantör: Tellusvägen 13 186 36 Vallentuna 08-514 307 60 www.bonthron-ewing.se
Automatisk Lyftmagnet LI-120 Lyftutrustning för professionellt bruk Automatisk kontroll Liten och kompakt Inbyggt, laddningsbart batteri Bistabil uppbyggnad Över tusen lyft på en laddning av batteriet Den automatiska lyftmagneten LI-120 designas och tillverkas av Ixtur Ltd. Den är en flexibel och användarvänlig, elektriskt styrd lyftanordning, som bygger på en kraftig magnetisk lyftkraft från en fast magnet. Den automatiska lyftmagneten LI-120 har en bistabil uppbyggnad, vilket innebär att den inte förbrukar energi så länge magnetens tillstånd förblir oförändrat. Magnetens tillstånd ändras med hjälp av en kort elektrisk puls, antingen manuellt via en knappsats eller automatiskt med ett inbyggt lastavkänningssystem. Den låga energiförbrukningen förlänger drifttiden och möjliggör en kompaktare design med inbyggt, laddningsbart batteri. Lyftkapacitet (kg) 120 100 80 60 40 20 0 0 1 2 3 4 5 6 7 8 9 10 11 12 13 Materialets tjocklek (mm) Den långa drifttiden, kompakta storleken och automatiska styrningen ger längre och effektivare arbetspass utan avbrott. TEKNISKA SPECIFIKATIONER Mått (Längd x bredd x höjd) Vikt Bärkraft Högsta lyftkapacitet Residualmagnetism Laddningstid Operativ tid med fulladdat batteri 125 mm x 125 mm x 200 mm 6,50 kg minst 360 kg (S235 S 12 mm) 120 kg (S235 S 12 mm) max. 10 kg max. 2 t 100 timmar i standbyläge eller 3000 magnet(de)aktiveringar (PÅ eller AV) Användningsförhållanden - Brukstemperatur: 0 C +50 C - Förvaringstemperatur: -20 C +35 C - Relativ luftfuktighet: 0 % 90 % Lyftkapacitet (%) 100 % 80 % 60 % 40 % 20 % 0 % 0 0,1 0,2 0,3 0,4 0,5 Luftspalt (mm) Din leverantör: Tellusvägen 13 186 36 Vallentuna 08-514 307 60 www.bonthron-ewing.se
07/2016 IXTUR PNEUMATIC MAGNETS Magnet with safety factor 3 Required plate thickness for nominal Optimized for round loads Suitable load diameter with round cylinder with safety factor 3 Required diameter for nominal Max. residual gripping (magnet OFF) Size ø x H or W x L x H Weight MAP-6 6 kg t > 4 mm - - - - 0.03 kg ø 35 x 35 mm 0.19 kg MAP-40 40 kg t > 8 mm - - - - 0.2 kg ø 65 x 50 mm 0.95 kg MAP-180 180 kg t > 25 mm - - - - 6 kg ø 120 x 82 mm 5.80 kg MAP-120R 120 kg t > 25 mm X ø > 0 mm 70 kg ø > 200 mm 6 kg ø 120 x 82 mm 5.80 kg MRP-46 46 kg t > 12 mm X ø > 20 mm 30 kg ø > 120 mm 4 kg 80 x 55 x 82.5 mm 1.80 kg MRP-170 170 kg t > 25 mm X ø > 25 mm 120 kg ø > 120 mm 30 kg 103 x 120 x 140 mm 10.7 kg Gripping versus material thickness and airgap Magnet gripping Required plate thickness for Gripping with plate thickness of: Gripping with flat and thick plate and an airgap of: nominal gripping 2 mm 4 mm 8 mm 0.1 mm 0.2 mm 0.4 mm MAP-6 18 kg t > 4 mm 13 kg 18 kg 18 kg 8.1 kg 4.5 kg 2.2 kg MAP-40 120 kg t > 8 mm 22 kg 57 kg 120 kg 79 kg 58 kg 34 kg MAP-180 540 kg t > 25 mm 26 kg 72 kg 160 kg 360 kg 270 kg 167 kg MAP-120R 360 kg t > 25 mm 19 kg 60 kg 175 kg 310 kg 270 kg 200 kg MRP-46 138 kg t > 12 mm 44 kg 91 kg 122 kg 103 kg 79 kg 44 kg MRP-170 510 kg t > 25 mm 56 kg 164 kg 400 kg 460 kg 410 kg 300 kg Definition of the terms gripping is the maximum mass the magnet can lift. To reach the nominal gripping, the load must be thick enough, there is no airgap and the material is mild steel S355. is the maximum mass the magnet can lift with a safety factor of 3. The nominal is one third of the nominal gripping. Airgap refers to any non-magnetic material between the magnet s gripping surface and the handled part. Airgap can be caused by e.g. paint, dirt, rust or plastic coating. Residual gripping, i.e. the gripping when the magnet is OFF, varies based on the material and structure of the gripped part. The residual is greatest as long as the part continously stays in contact with the magnet after the magnet has been turned from ON to OFF. With most of the load shapes, the gripping is only a fraction of the number given in the table above. Company Ixtur Ltd. is a Finnish magnet technology company established in 2010. Ixtur develops and manufactures permanent magnet based lifters, grippers and customer focused on energy-efficient magnet components and applications.
MAP-6, MAP-40 and MAP-180 magnets are especially designed for flat parts that fully cover the magnet s gripping surface. The magnets can also be used with narrow loads and perforated materials, but the gripping force is lower. Ixtur pneumatic magnets suit for various applications: lifters, robot grippers, fixtures and production automation. MAP-120R magnet s gripping surface is optimized for parts that do not fully cover the whole gripping surface of the magnet, e.g. cylinders, pipes and irregularly shaped objects. MRP magnets are suitable for gripping round and flat parts, as well as irregularly shaped objects. Videos of Ixtur magnets can be found from our YouTube channel. Please click the link Ixtur Magnets or scan the QR code above with your smartphone to access the channel. More information and brochures: www.ixtur.com Company Ixtur Ltd. is a Finnish magnet technology company established in 2010. Ixtur develops and manufactures permanent magnet based lifters, grippers and customer focused on energy-efficient magnet components and applications.
PLE-700 Automatic Plate Lifter 03/2015 TECHNICAL SPECIFICATIONS Model PLE-700 Lifting Capacity WLL 700 kg Dimensions 2.00m x 1.13m x 0.44m (L x W x H) Weight 150 kg Operating temperature -10 50 C Operating time 30 h standby or 1000 lifts with one battery charge Ixtur PLE-700 is a fully automatic plate lifter, which is designed to be used with crane and forklift. The product is completely cordless and easy to deploy. PLE-700 is a versatile solution for steel plates having thickness of 3 mm... 25 mm. The lifter is ideal for plate sizes of 1.25m x 2.50m and 1.50m x 3.00m. Due to Ixtur magnet technology, the magnets need energy only for changing their magnetic state. The load stays attached even if battery dies. PLE-700 main features - Fully automatic - Cordless functionality - Battery operated - Quickly changeable battery - 30 h on standby or 1000 lifts with one charge - Slim design - Easy deployment PLE-700 has slim design with only 44 cm of height. The lifter adapts to environments where space is limited e.g. low shelf clearance. More information: www.ixtur.com Company Ixtur Ltd. is a Finnish magnet technology company established in 2010. Ixtur develops and produces permanent magnet based lifters, grippers and customer focused on energy efficient magnet components and applications.