SVENSK STANDARD SS 876 00 10 Fastställd 2001-06-21 Utgåva 1 Sjukvårdstextil Vårdbäddar Brandkrav Extra högt antändlighetsmotstånd på madrass avsedd för speciellt ändamål Health care textiles Hospital beds with high performance requirement on ignitability (mentally deranged patient) ICS 11.140 Språk:svenska, engelska (bilaga) Tryckt i november 2001 Copyright SIS. Reproduction in any form without permission is prohibited.
Dokumentet består av 9 sidor. Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS Förlag AB, 118 80 STOCKHOLM Telefon: 08-555 523 10. Telefax: 08-555 523 11 E-post: sis.sales@sis.se. Internet: www.sisforlag.se
Sida 3 0 Orientering Denna standard ingår i en serie av standarder för sjukvårdstextilier. Standarden avser enbart brandkrav på madrass avsedd för speciellt ändamål. 1 Omfattning I denna standard redovisas fordringar beträffande brandkrav på madrass avsedd att andvändas för patient där extra höga brandkrav (antändlighet, värmeeffekt och rökutveckling) finns vid vård av patient som kan tänkas antända madrassen (exempelvis psykiskt sjuk patient). 2 Normativa hänvisningar NT Fire 032 Upholstered Furniture: Burning behaviour (Nordtest) SS 876 00 04 Produkter för vårdbädden Allmänna bestämmelser och kontroll SS-ISO 9705 Brandprovning Ytskikt Rumstest i fullskala Technical Bulletin 133. Flammability Test Procedure for Seating Furniture for use in Public occupancies. January 1991. 3 Krav Madrassens skum skall uppfylla de kravkriterier som anges nedan. Finns det ett ytskiktsöverdrag på madrassen så skall även detta uppfylla kravkriterierna. Rökproduktionen totalt under provning får maximalt uppgå till 50 m 2. Värmeeffektutvecklingen får maximalt uppgå till 55 kw. (Angående angivna enheter se även s. 9). Branden skall ha slocknat tre minuter efter det att brännaren tagits bort. Ingen glöd eller lågbrand får uppvisas. Det skall noteras i protokoll enligt NT Fire 032 hur skummet uppför sig och även hur ytskiktet uppför sig under brandförloppet. Likaså skall det noteras hur madrassen uppför sig efter det att brännaren avlägsnas. Provningsförloppet skall dokumenteras med foto och eventuellt (om beställaren så önskar) även videofilmas, så att både flamutbredning och skador på madrassen kan visualiseras. För typprovning och även vid kontroll vid reklamationstvist tas tre provenheter ut och alla skall uppfylla kraven som ställs i denna standard (se även 4.4.3 enligt SS 876 00 04). Vid ny leverans skall aktuellt provningsintyg kunna uppvisas för provning av en madrass. 4 Provningsmetod Madrassen skall provas enligt NT FIRE 032 med modifiering att antändningskällan ersätts med en fyrkantig gasbrännare (California TB 133 furniture test) se bilaga. Antändningen sker genom att gasbrännaren appliceras under två minuter med en värmeutveckling av 30 kw. Antändlighet, brandförlopp, värmeeffektutveckling och röktäthet skall utvärderas efter provningen.
Sida 4 Bilaga A (normativ) Furniture calorimeter test protocol 1 Scope and field of application This test procedure is intended for large scale testing of upholstered furniture. The specifications in NT FIRE 032 (Furniture Calorimeter) and in SS-ISO 9705 (smoke density measurement), in this document are required for performing a standardized Furniture Calorimeter test according to the CBUF procedure. 2 Overall description 2.1 Overall performance of the HRR measuring system The overall accuracy of the heat release measuring system shall meet the requirements given in NT FIRE 032. The time between the start of two scans shall be at maximum 5 sec. 2.2 Calculations The rates of heat release and mass loss rates shall be calculated according to Annex C of NT FIRE 032. The smoke production rate shall be calculated according to SS-ISO 9705, Annex F. 2.3 Weighing platform The weighing platform shall be constructed according to the specifications given in the NT FIRE 032. The slab shall consist of one single piece of 12 mm thick calcium silicate board having a density of about 850 ± 50 kg/m 3. The slab shall be 2400 mm x 1200 mm and be of a non-combustible material, e.g. calcium silicate boards. 2.4 The smoke collection hood In order to avoid a build up and spillage of smoke gases in the hood during the tests, the baffle plates in the plenum of the hood, described in the NT FIRE 032, shall be removed. 2.5 Ignition source The ignition source described in NT FIRE 032, wooden crib, shall be replaced with a gas burner. The burner to be used is the square ring burner developed at FRS and NIST (see figure 1 a-c). This burner is the primary ignition source in the California TB 133 furniture test. The gas burner shall be constructed according to the specifications in Technical Bulletin 133 of the State of California Department of Consumer Affairs. 2.5.1 Gas supply The burner shall be supplied with propane gas of at least 95% purity and at a flow rate of 0,65 g s -1 (19,5 L min -1 at 273 K and 100 kpa) which corresponds to a heat output of 30 kw. The gas flow shall be controlled to within 5% of the pre-set value. The burner shall be lit for 120 sec. Care should be taken to ensure that holes in the burner are kept clean.
Sida 5 NOTE 1. All tubing 1/ 2 OD, SS, 0.035 wall thickness. 2. All holes 1 mm in diameter. 3. All units are mm unless otherwise noted. PLAN VIEW OF SQUARE GAS BURNER Figure 1 a
Sida 6 L ~ 42"~ 107 mm SIDE VIEW OF SQUARE GAS BURNER Figure 1 b CROSS SECTIONAL VIEW OF EACH SIDE OF SQUARE GAS BURNER Figure 1 c 2.5.2 Application of the burner to a mattress The burner ring shall always be positioned level in the horizontal plane. The burner shall be positioned immediately over the centre of the mattress 25 mm above the mattress-surface. 3 Test set-up The basic Furniture Calorimeter test set-up shall be according to the specifications in NT FIRE 032 except as provided below. 3.1 Environment around the burning sample The environment around the sample shall be a draught free area with no more than two enclosing walls. An enclosing wall is defined as a wall closer than 2,0 m from the outer edge of the smoke collection hood.