SVENSK STANDARD SS-ISO 965-4 Fastställd 2003-08-01 Utgåva 1 Metriska ISO-gängor för allmän användning Gängtoleranser Del 4: Gränsmått för varmförzinkade utvändiga gängor avsedda för användning tillsammans med invändiga gängor gängade till toleranskvalitet H eller G efter förzinkning ISO general purpose metric screw threads Tolerances Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing ICS 21.040.10 Språk: engelska, svenska Publicerad: december 2003 Copyright SIS. Reproduction in any form without permission is prohibited.
Dokumentet består av 13 sidor. Upplysningar om sakinnehållet i standarden lämnas av SIS, Swedish Standards Institute, tel 08-555 520 00. Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS Förlag AB, 118 80 STOCKHOLM Telefon: 08-555 523 10. Telefax: 08-555 523 11 E-post: sis.sales@sis.se. Internet: www.sis.se
Den internationella standarden ISO 965-4:1998 gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av ISO 965-4:1998 med svensk översättning. Standarden ersätter SS 3193, utgåva 2. Efter det att ISO 965-1:1998 gavs ut har en ny utgåva av följande standard givits ut: ISO 898-1:1999, Fästelement Mekaniska egenskaper för fästelement av kolstål och legerade stål Del 1: Skruvar och pinnskruvar Denna standard har fastställts som europastandard med beteckningen EN ISO 898-1:1999 samt fastställts och givits ut som svensk standard med beteckningen SS-EN ISO 898-1, utgåva 1. The International Standard ISO 965-4:1998 has the status of a Swedish Standard. This document contains the official English version of ISO 965-4:1998 with a Swedish translation. This standard supersedes the Swedish standard SS 3193, edition 2. Since ISO 965-1:1998 was published a new edition of the following standard has been published: ISO 898-1:1999, Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs This standard has been approved as a European standard under the designation EN ISO 898-1:1999 and approved and published as a Swedish standard under the designation SS-EN ISO 898-1, edition1.
Page 1 ISO 965-4:1998 Provläsningsexemplar / Preview Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 965-4 was prepared by Technical Committee ISO/TC 1, Screw threads, Subcommittee SC 2, Tolerances. ISO 965 consists of the following parts, under the general title ISO general purpose metric screw threads Tolerances Part 1: Principles and basic data Part 2: Limits of sizes for general purpose bolt and nut threads Medium quality Part 3: Deviations for constructional screw threads Part 4: Limits of sizes for hot-dip galvanized external threads to mate with internal threads tapped with tolerance position H or G after galvanizing Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
Sida 1 ISO 965-4:1998 Förord ISO (Internationella Standardiseringsorganisationen) är en världsomspännande sammanslutning av nationella standardiseringsorgan (ISO-medlemmar). Utarbetandet av internationella standarder sker normalt i ISOs tekniska kommittéer. Varje medlemsland som är intresserat av arbetet i en teknisk kommitté har rätt att bli medlem i den. Internationella organisationer, statliga såväl som icke-statliga, som samarbetar med ISO deltar också i arbetet. ISO har nära samarbete med International Electrotechnical Commission (IEC) i alla frågor rörande elektroteknisk standardisering. Förslag till internationella standarder som godkänts av de tekniska kommittéerna sänds till medlemsländerna för röstning. För publicering av en internationell standard krävs att minst 75 % av de röstande medlemsländerna godkänner förslaget. Den internationella standarden ISO 965-4 har utarbetats av ISO/TC 1, Screw threads, Subcommittee SC 2, Tolerances. ISO 965 består av följande delar under huvudtiteln Metriska ISO-gängor för allmän användning Gängtoleranser: Del 1: Principer och grundläggande data Del 2: Gränsmått för utvändiga och invändiga gängor för allmän användning Toleranskvalitet medel Del 3: Avmått för konstruktionsgängor Del 4: Gränsmått för varmförzinkade utvändiga gängor avsedda för användning tillsammans med invändiga gängor gängade med toleransläge H eller G efter förzinkning Del 5: Gränsmått för invändiga gängor avsedda för användning tillsammans med varmförzinkade utvändiga gängor med max. mått enligt toleransläge h före förzinkning.
Page 2 ISO 965-4:1998 Provläsningsexemplar / Preview ISO general purpose metric screw threads Tolerances Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing 1 Scope This part of ISO 965 specifies deviations and limits of sizes for pitch and crest diameters for ISO general purpose metric external screw threads conforming to ISO 262 having a basic profile according to ISO 68-1. External screw threads according to this part of ISO 965 are intended to mate with internal screw threads tapped with tolerance position H or G after hot dip galvanizing. The limits of sizes for the tolerance quality specified are derived from tolerances specified in ISO 965-1 and the fundamental deviations according to the following formula: where es az = (300 + 20P) es is expressed in micrometres; P is expressed in millimetres. Products made with thread tolerances in accordance with this part of ISO 965 may show failure at lower ultimate tensile loads than those specified in ISO 898-1 due to reduction of the stress area. External screw threads with thread tolerances according to this part of ISO 965 must not be mated with internal screw threads with thread tolerances according to ISO 965-5 because such combinations will create severe risk for thread stripping. NOTE If the tolerance class 6az is not specified the external screw threads are to mate with internal screw threads with tolerance position 6AZ if the products are centrifuged and with hot-dip galvanized internal screw threads with tolerance position 6AX if the products are not centrifuged. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 965. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 965 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 68-1:1998, ISO general purpose screw threads Basic profile Part 1: Metric screw threads. ISO 262:1998, ISO general purpose metric screw threads Selected sizes for screws, bolts and nuts.