Installationsguide och beskrivning av Gewa Amplifier IR Installation guide and description of Gewa Amplifier IR
2
INNEHÅLL/CONTENTS SVENSKA...4 Inledning... 4 Installera Progress PC... 4 Beskrivning av olika delar... 5 Manöverkontakter... 6 Högtalare/hörlurar och mikrofon... 6 Reläutgång... 6 Spela in IR-koder... 7 Inspelning... 7 Fastsättning... 8 Rengöring... 8 Användningsmiljö... 8 Återvinning av elavfall... 8 Tekniska data... 9 Överensstämmelse med Medicintekniska direktivet... 9 ENGLISH...10 Introduction... 10 Installing Progress PC... 10 Different parts... 11 Control switches... 11 External speaker/earphones and microphone... 12 Relay output... 12 Recording IR codes... 12 Mounting... 14 Cleaning... 14 Environment conditions... 14 Recycling Waste Electrical and Electronic Equipment... 14 Technical data... 15 Conformity with the Medical Devices Directive... 16 3
Svenska Inledning Gewa Amplifier IR har en inbyggd högtalare för att ge ett bättre och högre ljud. Den är försedd med en inbyggd IR-module vilket möjliggör styrning av TV, video, stereo mm. Mjukvaran Progress PC möjliggör detta. Gewa Amplifier har två ingångar för yttre manöverkontakter för styrning genom scanning. Installera Progress PC För att undvika problem vid igångkörning av programvara och hårdvara är det viktigt att man följer installationsanvisningen. OBS! Börja med att installera mjukvaran innan Gewa Amplifier kopplas in. Progress PC är kompatibel med Win 98 andra utgåvan, Win 2000 och Win XP. Gör enligt följande för att installera programvara och hårdvara: 1. Sätt i CD-skivan Progress PC i datorns CD-enhet. Vänta tills en installationsguide visas på skärmen. Detta kan ta några sekunder. Om installationsguiden inte visas: Gå till Start-menyn, Välj Kör och skriv D:\setup (byt ut D om din CD-enhet har en annan beteckning). Klicka på OK. 2. Installera Progress PC först. Följ installationsguiden. 3. Installera sedan USB-drivrutiner. Följ installationsguiden. 4. Anslut Gewa Amplifier till datorns USB-port när instruktion ges. Drivrutin för USB Serial Converter installeras först och sedan drivrutin för USB Serial Port. Välj automatisk installation. Vid installation i Win 98 måste man även ange att drivrutiner skall hämtas från CD, sökvägen, D:\Drivers\w98_w2k_wxp. 5. Ta ur CD-skivan ur CD-enheten. 6. Anslut Audio-kontakten. Ev. erfordras en adapterkabel (052528). Medföljer ej, måste beställas separat. 7. Avsluta med att starta om Progress PC och kontrollera att Gewa Amplifier sänder. 4
Beskrivning av olika delar 052528 Adapter (Ingår ej) Manöverkontakt 1 och 2 Volymkontroll för inbyggd högtalare Utgång för extern högtalare/hörlurar Ingång för extern mikrofon Reläutgång 5
Manöverkontakter Två manöverkontakter kan anslutas för användning vid scanning. Anslutningskontakt skall vara 3,5 mm telepropp. Endast CE-märkta manöverkontakter får kopplas in. Varning! Elektroder som fästes på huden eller invasibla manöverkontakter får ej anslutas till Future Pad. Högtalare/hörlurar och mikrofon Externa högtalare/hörlurar och mikrofon kan anslutas. Anslutningskontakter 3,5 mm telepropp. Yttre mikrofon bör användas vid inspelning. Ljudvolym för externa högtalare/hörlurar justeras i Windows-inställningar. Ljudvolym för den inbyggda högtalaren justeras med knapparna på Gewa Amplifier men påverkas också av Windows-inställningar. Gör enligt följande för att ställa in en bra grundvolym i den inbyggda högtalaren i Gewa Amplifier: 1. Gå till Windows-inställningar. Sökväg: Start\Kontrollpanelen\Ljud och ljudenheter. 2. Ställ volymen lågt i Windows-inställningar. 3. Ställ upp volymen på Gewa Amplifier maximalt. Se bild sid. 5. 4. Testa ljudet i Gewa Amplifier. 5. Öka volymen i Windows-inställningar tills ljudet är maximalt utan att det låter illa i högtalarna. Gör enligt följande för att ställa in en bra grundvolym för mikrofon: Gå till Windows-inställningar. Sökväg: Start\Kontrollpanelen\Ljud och ljudenheter\ljudenheter\volume (Inspelning av ljud). Bocka för mikrofon och höj volym till maximalt. Reläutgång Reläutgången kan användas för att påkalla uppmärksamhet, t.ex. en radiosändare som är ansluten. Anslutningskontakt 2,5 mm telepropp. Max belastning 120 ma, 24 V AC/DC. Reläutgången fungerar bara med Progress PC. 6
Spela in IR-koder För att kunna styra t.ex. TV, Video, Stereo, DVD, leksaker, lampor m.m. krävs att dessa apparater har en fjärrkontroll som sänder infrarött ljus (IR). En TV t.ex. har för det mesta en fjärrkontroll (IR) som används för att styra olika funktioner. Det är denna fjärrkontroll som ska användas för att lära in IR-koder. Andra apparater som t.ex. lampor, telefon, porttelefon och dörrautomatik har inte någon sådan fjärrkontroll. Gewa har lösningar som gör det möjligt att även styra dessa apparater. GewaLink-kanaler 00-127 ligger fabriksinställda och kan användas för att styra Gewas egna produkter. Kontakta Gewa eller Gewas återförsäljare för mer information. När man spelar in en IR-kod används en minnesplats. Totalt 256 minnesplatser finns till förfogande. Inspelning Innan man börjar spela in en IR-kod skall man vara förvissad om att batterierna i fjärrkontrollen har full kapacitet. Vistas ej i starkt ljus vid inlärning (t.ex. solljus). För att få bra kvalité på den inspelade IR-koden behöver avståndet mellan fjärrkontrollen och sändarenheten vara rätt. Detta avstånd är olika för olika fjärrkontroller och bör därför kontrolleras innan man spelar in IRkoder från nya fjärrkontroller. När man spelar in skall enheterna vara placerade enligt figur. Det exakta förfarandet finns att läsa i manualen för Progress PC. IR-sändare riktas mot sensor vid inspelning av IR 7
Fastsättning Kardborreband medföljer för att kunna fästa Gewa Amplifier på dator. Rengöring Innan rengöring skall laddare vara bortkopplad. Gewa Amplifier görs rent med en mycket hårt urvriden trasa som doppats i vatten med lite diskmedel i. Efter rengöring torkas den med en torr trasa. Användningsmiljö Gewa Amplifier är avsedd att användas inomhus i torr miljö. Återvinning av elavfall Gewa Amplifier innehåller elektronik som skall återvinnas när produkten kasseras. Lämnas till miljöstation för elavfall. 8
Tekniska data Max belastning reläutgång: Max 120 ma, 24V AC/DC Reläutgång: 2,5 mm telepropp 2-pol Ingång manöverkontakt: 3,5 mm telepropp 2-pol Utgång extern 3,5 mm telepropp 3-pol högtalare/hörlurar: Ingång mikrofon: 3,5 mm telepropp 3-pol Dataanslutning: USB Audioanslutning: 2,5 mm telepropp 3-pol Programmeringsplatser: 256 EMC-standard emission: EN 61000-6-4:2001, EN 60601-1-2:2001 immunitet: EN 60601-1-2:2001 Användningsmiljö: Inomhus, torr miljö Temperaturområde: 0 - +40 C Vikt: 240 gr Överensstämmelse med Medicintekniska direktivet Gewa Amplifier IR marknadsförs som ett tekniskt hjälpmedel för personer med handikapp och uppfyller kraven i Medicintekniska direktivet 93/42/EEC vilket t.ex. inkluderar relevanta krav för EMC och elektrisk säkerhet. 9
English Introduction Gewa Amplifier IR is equipped with a built-in loudspeaker for better and louder sound. It s equipped with an IR-module which provides control of TV, VCR, stereo a.s.o. The software Progress PC makes this possible. The Gewa Amplifier has two inputs for external control switches used for scanning control. Installing Progress PC To avoid problems when starting software and hardware it is important to follow the installation instructions. Note! Always install the software before connecting The Gewa Amplifier to the USB port. Progress PC is compatible with Win 98 second edition, Win 2000 and Win XP. Install software and hardware by the following procedure: 1. Insert the CD Progress PC in the CD unit on the computer. Wait until an installation guide is shown on the screen. It might take a few seconds. If the installation guide is not shown: Go to Start-menu, Select Drive and write D:\setup (exchange D if the CD unit has another designation). Click OK. 2. Install Progress PC first. Follow the installation guide. 3. Then install the USB driver. Follow the installation guide. 4. Connect Gewa Amplifier to the USB port on the computer when instruction is given. First the driver for the USB Serial Converter will be installed and then the driver for the USB Serial Port. Select automatic installation. When installing in Win 98 it must be specified that you must pick up drivers from the CD, path, D:\Drivers\w98_w2k_wxp. 5. Remove the CD from the CD-unit. 6. Connect the Audio plug to the computer. An adapter cable (052528) may be required. Cable is not included, must be ordered separately. 7. Restart Progress PC and check that Gewa Amplifier is transmitting. 10
Different parts 052528 Adapter (Not included) Volume control for built-in speaker Control switch 1 and 2 Input for external microphone Output for external speaker /earphones Relay output Control switches Two control switches can be connected when using scanning. The attachment plug should be a 3,5 mm jack plug. No other than CE-marked control switches shall be connected. Warning! Electrodes that are attached to the skin or invasible switches must not be connected to the Future Pad. 11
External speaker/earphones and microphone External speakers/earphones and a microphone can be connected. Attachment plugs 3,5 mm jack plug. External microphone should be used when recording. The volume for external speakers/earphones shall be adjusted in Windowssettings. The volume on the built-in speaker is adjusted by the buttons on the Gewa Amplifier but is also affected by the Windows settings. Set a good basic volume in the built-in speaker on the Gewa Amplifier by the following procedure: 1. Go to Windows settings: Path: Start\Control Panel\Sound and Sound devices. 2. Set the volume low in Windows settings. 3. Turn up the volume to a maximum in the Gewa Amplifier See picture page 11. 4. Test the sound in Gewa Amplifier. 5. Increase the volume in Windows settings until the sound is at a maximum and there is no distortion on the speakers. Set a good basic volume for the microphone by the following procedure: Go to Windows settings. Path: Start\Control Panel\Sound and Sound devices\audio\volume (Sound recording). Select microphone and turn up the volume to maximum. Relay output The relay output can be used to call attention, e.g. a connected radio transmitter. Attachment switch 2,5 mm jack plug. Max load 120 ma, 24 V AC/DC. The relay output does only work with Progress PC. Recording IR codes To be able to control a TV, for example, or a Video, Stereo, DVD, toys, lamps etc. These devices must have a remote control unit that emits infrared light (IR). Most TVs have a remote control unit that is used to control various functions. It is this remote control unit that is to be used to teach IR codes. Other devices such as lamps, telephone, hall telephone and door opener do not have any remote control unit. Gewa have solutions that makes it possible to control also these devices. GewaLink-kanaler 00-127 are default and can be used to control Gewa s own products. Please contact Gewa or Gewa s Gewas representatives for more information. One memory location is used for each IR code that is recorded. There are 256 memory locations available. 12
Recording Before starting to record IR codes, ensure that the batteries in the remote control have full capacity. Do not place the devices in bright light (such as sunlight) during the learning procedure. In order to obtain good results when recording IR codes the distance between the remote control unit and the transmitting unit must be correct. This distance differs from one remote control to another and thus you should check the distance before recording new IR codes from the remote control unit. When recording the units should be placed according to the figure below. How to proceed exactly is described in the software manual. The IR transmitter is directed to the sensor when recording IR 13
Mounting Velcros are included to attach Gewa Amplifier to a computer. Cleaning Before cleaning the charger must be disconnected. The Gewa Amplifier can be cleaned with a damp cloth (weak solution of washing up liquid). After cleaning, wipe with a dry cloth. Environment conditions The Gewa Amplifier is to be used indoors in a dry environment. Recycling Waste Electrical and Electronic Equipment The Gewa Amplifier IR contains electronic components that must be recycled. When the product is disposed of, hand it in to a recycling centre for waste electrical of electrical and electronic equipment. 14
Technical data Max load relay outputs: Max 120 ma, 24V AC/DC Relay output: 2,5 mm jack plug 2-pole Input control switch 3,5 mm jack plug 2-pole Output external 3,5 mm jack plug 3-pole speakers/earphones: Input microphone: 3,5 mm jack plug 3-pole Data connection: USB Audio connection: 2,5 mm jack plug 3-pole Programming locations: 256 EMC-standard emission: EN 61000-6-4:2001, EN 60601-1-2:2001 immunity: EN 60601-1-2:2001 Environment conditions: Indoors in a dry environment Operating temperature: 0 - +40 C Weight: 240 g 15
Conformity with the Medical Devices Directive Gewa Amplifier IR is marketed as a technical aid for persons with disabilities and meets the requirements in the Medical Devices Directive 93/42/EEC including relevant EMC and electrical safety requirements. Gewa AB BOX 92, SE-191 22 SOLLENTUNA, SWEDEN TEL: +46 (0)8-594 694 00 TEXTTEL: +46 (0)8-594 694 18 FAX: +46 (0)8-594 694 19 E-MAIL: info@gewa.se WEB: www.gewa.se Art.no: 808730. Doc: Manual Gewa Amplifier IR, SE, GB. Ver: A. Date: 2007-02-05. 16