DETALJMONTERINGSANVISNING ASSEMBLY INSTRUCTION, DETAILED VERSION GUNGSTÄLLNINGAR SWINGSETS
Steg för steg, monteringsinstruktion: 1. Mät hela ytan och se till att aktuell produkts krav på säkerhetsyta efterlevs. 2. Gräv samtliga hål enligt grävskiss på sida 2 i Monteringsanvisningen. 3. Montera samtliga gungleder på gungbommarna. Sid.4 4. Montera på markfundamenten samt betongfundamenten på gungbenen. Sid. 5, 10 5. Montera samman samtliga benpar utan att spänna åt. Sid. 6-7 6a. Placera bommen / bommarna på plats i klykan som bildas av benparet/-paren. Vid skarvbommar börjar man lämpligast denna procedur vid skarvarna. Sid. 8-9 6b. Se till att bommen ligger rätt orienterad och montera samman gungbommen och benparen med de två/fyra genomgående bultarna från stålvinkeln genom bommen. Sid 8-9. 6c. Därefter kläms gungbommen åt mellan gungbensparen genom att dra isär benen. Använda franska träskruv genom de förborrade hålen på benen för att säkra montaget. Sid. 8-9. 7. Sätt temporära stagningar mellan benparen och lyft sedan hela gungställningen på plats i de förberedda hålen. Väg in, staga upp återfyll sedan grävhålen. 8. Plocka ner alla temporära stag och montera gungsitsarna. Sid. 11 9. Efter genomgången och godkänd slutbesiktning (se Produktinformationsblad, Inspektion av färdig produkt) kan allmänheten ges tillträde till gungställningen. 2
Step by step, assembly procedure: 1. Measure the site where the equipment is supposed to be placed. Ensure that the demands for safety zone for the equipment are met. 2. Dig the holes according to the sketch on page 2 in the Assembly instruction. 3. Attach all swing joints onto the crossbeam(s). Page 4 4. Attach the metal ground anchors onto the swingsets legs and then attach the prefabricated concrete foundations onto the ground anchors. Page 5, 10 5. Assemble the leg pairings without tightening the bolts. Page 6-7 6a. Place the crossbeam(s) as intended in the fork of the leg pairings. When the swingset uses a combination of several crossbeams, it is suitable to begin this process at one of the joints. Page 8-9 6b. Make sure that the crossbeam is properly positioned and then attach it onto the leg pairings through the two/four bolts as seen on page 8-9. 6c. Next to this, squeeze the crossbeam between the leg pairings by pulling them (the legs) apart from each other. Make the final attachment with the screw through the legs into the crossbeam as on page 8-9. 7. Put temporary bracings in between the legs to ensure the A -like shape when lifting the entire swing set in place into the previous dug holes. Make sure the swing set is in level, then brace it in position and carefully refill the holes. 8. Remove the temporary braces and install the swing seats. Page 11. 9. After being checked and cleared according to the Post installation inspection in the Product information sheet, the public can be allowed to use the product. 3
1 2 3 4 Artikelnummer reservdelar / Art. no. spare parts: 1. Gungled / Swing joint - 50181400 2. Låsmutter / Insert locking nut M12-91001200 3. Bricka / Washer 13x30x3 mm - 91021500 4. Plastplugg / Plastic hole cover D: 35 mm - 39960500 39960500 91001200 91021500 50181400 OBS! Mycket viktigt! Gunglederna skall sitta ordentligt fast i gungbommen och inte glappa. Därför måste de efterdras med jämna mellanrum. Vid kontroll ska gungleden efterdras vid minsta tendens till glapp. Please observe the importance of tightening the nuts properly in order to minimize the stress on the swing joints. If this is overseen with, the life expectancy of the swing joint is severly shortened. 4
1 2 3 4 5 6 7 Artikelnummer reservdelar / Art. no. spare parts: 1. Markfundament vfz / Metal post shoe - 27210100 2. Bult / Bolt M12x120 mm - 92121200 3. Vagnsbult / Carriage bolt M12x140 mm - 93121400 4. Bricka / Washer 13x30x3 mm - 91021500 5. Låsmutter / Insert locking nut M12-91001200 6. Plastplugg / Plastic hole cover 35 mm - 39960500 7. RF Torx / Torx screw 6,3x38 mm - 97160400 Gungben 91021500 91001200 97160400 x 4 39960500 92121200 93121400 91001200 27210100 5
1 2 3 4 5 6 7 Artikelnummer reservdelar / Art. no. spare parts: 1. Gungben / Post for swing stand - 13022800/13022500* 2. Stagjärn / Metal support - 27510000 3. Vagnsbult / Carriage bolt M12x180 mm - 93121800** 3. Vagnsbult / Carriage bolt M12x200 mm - 93122000*** 4. Bricka / Washer 13x30x3 mm - 91021500** 5. Låsmutter / Insert locking nut M12-91001200 6. Plastplugg / Plastic hole cover D: 35 mm - 39960500** 7. Mutterskyd plast M12 / Plastic nut cover M12-91121200 * För 5120-1 / For 5120-1 ** För start- och ändsektion / For start- and end section ** För skarv / For middle section Sprängskiss av montage på nästa sida / Exploded assembly sketch on next page 6
Montering vid start / ände / Assembly at start and end sections 27510000 94121800 39960500 91001200 91021500 Montering vid gungbomsskarv / Assembly at middle section 27510000 91121200 93122000 91001200 7
1 2 3 4 7 5 6 8 Artikelnummer reservdelar / Art. no. spare parts: 1. Skarvbeslag gungställning / Metal joint connector - 51301000* 2. Övre vinkel gungställning / Metal fitting - 51201500 3. Vagnsbult/Carriage Bolt M12x140 mm, M12x160, M12x180-93121400, 93121600, 93121800 4. Bricka / Washer 13x30x3 mm - 91021500 5. Mutter M12 / Nut M12-91001200 6. Fransk skruv / Coach screw 12x140 mm - 98121400 7. RF Torx / Round head, Torx screw 6,3x38 mm - 97160400 8. Plastplugg / Plastic hole cover D: 35 mm - 39960500 9. Mutterskydd plast M12 / Plastic nut cover M12-91121200 9 Bom/Startbom Mellanbom Ändbom Cross beam Cross beam start. section Middle section End section 5120-1 13039002 - - 5131-13025001 - - 5132-13039002 - - 5133-13039102 - 13025201 5134-13039102 - 13039102 5136-13039102 13039302 13039102 5141-13039003 - - 5141-2 - 13039103-13039102 5142-13039104 - - 5143-13039104 - 13025201 5144-13039104 - 13039102 5146-13039104 13039302 13039102 *Används för skarvning av gungbom. Gäller ej 5131, -32, -41-42 eller vid ändarna av gungställningen. * Is used only when joining together two cross beams. Isn t used at all for 5131, -32, -41, -42 or at the outer ends of the swing set. Sprängskiss på gungbomsmontage och gungbomsskarvning, se nästa sida. For exploded view of assembly, see next page. 8
Montering vid gungbomsskarv / Assembly at middle section 97160400 91121200 51201500 91001200 51301000 A Använd det inre hålet! Use the inner hole! Detail A 91021500 98121400 39960500 93121600 Sammansatt Assembled Montering vid ände / Assembly at start and end sections 97160400 51201500 39960500 91001200 91021500 50 mm 91021500 98121400 39960500 5120-5146 -> 93121400 5153-5184 -> 93121800 Sammansatt Assembled 9
Artikelnummer reservdelar / Art. no. spare parts: Betongfundament / Pre-casted concrete foundation - 59932100 Locking bushing - Kontakta Slottsbro AB / Contact your local dealer. Låskil Betongfundament 10
Artikelnummer reservdelar / Art. no. spare parts: Gungsits / Swing seat - Enligt beställning. Se order eller kontakta Slottsbro AB. / According to specification upon ordering. Contact your local dealer. Schackel - 59932100 Plastbussning / Plastic bushing - 50185000 11
12
Kontakt: SLOTTSBRO AB Kangerudsvägen 10 664 40 SLOTTSBRON Tel växel: 0555-307 20 Fax: 0555-300 71 info@slottsbro.se www.slottsbro.se