Operting Instrutions Vlve Module Comintions Vlve module omintions with sequene vlves (see pge 4) nd pressure reduing vlves (see pge 6) for every lmping funtion s omintions onsisting of one input vlve nd up to 3 series vlves These operting instrutions re ville for vlve module omintions of the following types: 4401-893 Input module 4401-894 Series module 6853-91x Comintions Trget group of this doument Fitters nd setters of mhine tools. They hve to e fmilir with the hndling nd mounting of hydruli omponents. Provided use Vlve module omintions re used to ontrol omplex hydruli lmping fixtures to effet positioning, lmping nd supporting of workpiees in defined sequene. Sfety Troules of funtioning Protet ginst swrf, otherwise hek vlves might not sel. Instrutions for sfe opertion Troules of funtioning The used pressure reduing vlves re designed without lekge oil port nd nnot ompenste inresing seondry pressure ( e. g. due to temperture rise, externl fores or dmge of the vlve set y swrf). Remedy: Instll in ddition pressure relief vlve. Swrf or ontmintion in the hydruli oil led to inresed wer or dmge t the guides, running surfes nd sels. The mximum operting pressure nd the dmissile flow rte of the vlve must not e exeeded. Use hydruli oil s per Roemheld dt sheet A 0.100. These modules omine sequene vlves nd pressure reduing vlves to determine the lmping sequene nd the lmping pressure of different lmping iruits. The vlve module omintion onsists of n input module nd up to 3 series modules. elements of the input module: - Flow ontrol vlve with onneted input filter for oth inputs to redue the flow rte nd to filter the fluid - Pilot-ontrolled hek vlve to protet the lmping iruit in the se of pressure drop or due to line rek - Pressure reduing vlve to redue the pressure for the first ontrol funtion t the fixture - Two miniture mesuring onnetions to onnet pressure guge for pressure djustment. elements of the series module: - Sequene vlve to relise one or severl swithing sequenes (onneted in series in the linked rrngement) - Pressure reduing vlve to redue the pressure in the orresponding swithing sequene - Miniture mesuring onnetion to onnet pressure guge for pressure djustment. Römheld GmH Postfh 12 53 D-35317 Luh Phone + 49 (0) 64 05 / 89-0 Fx +49 (0) 64 05 / 89-211 www.roemheld.om Pge 1/8
Exmple with n = 4 funtions (6853-914) Input module Series module g f e d 2 1 All figures re shemti figures. d Sequene vlve Port for pressure guge G¼ Pressure reduing vlve Mesuring port e f g Pilot-ontrolled hek vlve Input filter Flow ontrol vlve Instlltion Any mounting position of the vlve module omintion is possile. Provide Hydruli the threds onnetion in the fixture. Connet hydruli lines to qulifying stndrds, py ttention to srupulous lenness! See lso Roemheld dt sheets A0.100, F9.300, F9.310 nd F9.360. Use only fittings "srewed plug B" s per DIN 3852 (ISO 1179). Do not use seling tpe, opper rings or oned fittings. Chek seling of the hydruli onnetions! Port A Clmping B Unlmping F1 1 F2 2 F3 3 F4 4 M Pressure guge R Return Adjust lmping iruits Chek the swithing pressure during djustment of lmping iruit with pressure guge. For sequene nd pressure reduing vlves the following is vlid on priniple: Inrese the pressure y srewing in (lokwise) the djustment srew. Redue the pressure y srewing out (ounterlokwise) the djustment srew. Strting position Srew in ompletely the djustment srew t the flow ontrol vlve (1g), then srew out y 2 revolutions. All sequene vlves (1): Unsrew lok nut nd srew in ompletely the djustment srew. All pressure reduing vlves (1): Unsrew lok nut nd srew out ompletely the djustment srew. Swith on pump. Adjust lmping pressure for funtion 1 nd 2 Srew in djustement srew t pressure reduing vlve for F1 until the desired lmping pressure is otined (hek t the pressure guge). Srew out djustment srew t sequene vlve for F2 until the ylinder t F2 extends (lmps). Tighten lok nuts. Srew in djustement srew t pressure reduing vlve for F2 until the desired lmping pressure is otined (hek t the pressure guge). Proeed the sme wy for the remining lmping iruits. Crry out some lmping nd unlmping opertions to ensure proper opertion. Sujet to hnges without notie. Pge 2/8
Mintenne Chek if the hydruli ports re tight (visul ontrol). Mteril dmge Due to strong ontmintions of the input filters (1f) the pressure n inrese. Therey the filters s well s other omponents n e destroyed. Clen the input filters t regulr intervls. Dt sheets Types Corresponding dt sheets 4401-xxx, 6853-xxx C2.960 2951-4xx C2.9512 2953-1xx C2.9533 429 C2.954 3887-030 D8.755 9208-129 C2.9501 Generl hrteristis Prt-no. 4401 6853 Mx. operting pressure (primry r 500 side) Rnge of djustment r 30 380 Flow rte per lmping iruit l/min 8 Relesing pressure for hek vlves p Z r 0,05 p A + 7 Sujet to hnges without notie. Pge 3/8
Operting Instrutions Sequene Vlves ND 4 Sequene vlves with hek vlve for tue onnetion or mnifold mounting lso s omintions onsisting of one input vlve nd up to 5 series vlves These operting instrutions re ville for sequene vlves of the following types: 42x 44x Trget group of this doument Fitters nd setters of mhine tools. They hve to e fmilir with the hndling nd mounting of hydruli omponents. Provided use Sequene vlves re used in power workholding iruits for pressure dependent sequene ontrol. Severl sequene vlves n e mnifold mounted together to form ttery with only one ommon P-line for sequene ontrol. Sfety Instrutions for sfe opertion Swrf or ontmintion in the hydruli oil led to inresed wer or dmge t the guides, running surfes nd sels. The mximum operting pressure nd the dmissile flow rte of the vlve must not e exeeded. Use hydruli oil s per Roemheld dt sheet A 0.100. After otining determined pressure, sequene vlves onnet further lmping iruit t the seondry port A. Troules of funtioning Protet ginst swrf, otherwise hek vlves might not sel. Sujet to hnges without notie. Pge 4/8
Instlltion Any mounting position of the vlves is possile. 44x 42x 2 All figures re shemti figures. Adjustment srew Lok nut Sfety plug Hydruli onnetion with tues (420 nd -440) Clen the support surfes. Fsten the vlve t the flnge with srews M5. Hydruli mnifold-mounting onnetion (429 nd -449) Drill holes for hydruli oil supply nd return in the fixture. Grind flnge surfe. Clen the support surfes. Fsten the vlve with O-rings on the fixture. Sequene vlve ttery omintions These tteries onsist lwys of one input vlve nd up to five series vlves. Only one pressure line is required to port P of the input vlve (onnetion y tues or y mnifold mounting possile, see ove). Oil supply to the series vlves is mde without tues through drilled hnnels. Assemle vlves with inserted O-rings nd srew with threded olts M5. Remove the srew plug of the input vlve nd lose the port P of the lst series vlve with this plug. Provide Hydruli the threds onnetion in the fixture. Connet hydruli lines to qulifying stndrds, py ttention to srupulous lenness! See lso Roemheld dt sheets A0.100, F9.300, F9.310 nd F9.360. Use only fittings "srewed plug B" s per DIN 3852 (ISO 1179). Do not use seling tpe, opper rings or oned fittings. Chek seling of the hydruli onnetions! Port A P Output (seondry side) Pressure supply (primry side) Adjust swithing pressure Chek the swithing pressure during djustment with pressure guge. Unsrew lok nut (1). Inrese swithing pressure y srewing in (lokwise) the djustment srew (1). Redue the swithing pressure y srewing out (ounterlokwise) the djustment srew. Tighten lok nut. Crry out some lmping nd unlmping opertions to ensure proper opertion. Sequene vlve ttery omintions For sfe funtioning of the sequene ontrol the minimum differene in pressure from vlve to vlve, indited in the hrt of hrteristis, hs to e kept. Troule shooting Troule Oil emerges t the sfety plug (1). Mintenne Chek if the hydruli ports re tight (visul ontrol). The vlve itself is mintenne free. Dt sheets Cuse / Remedy Sel defet, pressure uild up in the over - Exhnge sel kit, nd press in gin sfety plug Types Corresponding dt sheets xxx C2.954 Generl hrteristis Prt-no. 420 440 429 449 Type Individul vlve Individul vlve Connetion tue mnifold mounting Port A, P G1/4 G1/4 Ø 5 Ø 5 427 441 Sequene input vlve tues or mnifold mounting G1/4 + Ø5 G1/4 + Ø5 428 442 Sequene series vlve mnifold mounting G1/4 G1/4 Mx. operting pressure (primry side) r 500 500 500 500 Rnge of djustment r 10 150 10 450 10 150 10 450 10 150 10 450 10 150 10 450 Minimum differene in pressure r 25 50 25 50 Mx. flow rte l/ min 8 8 8 8 Sujet to hnges without notie. Pge 5/8
Operting Instrutions Pressure Adjusting System Pressure reduing vlves with hek vlve with nd without lekge oil port s threded-ody vlve, for pipe onnetion or flnge mounting These operting instrutions re ville for pressure reduing vlves of the following types: 2953-100 2953-110 2953-111 2953-400 2953-500 2953-600 Trget group of this doument Fitters nd setters of mhine tools. They hve to e fmilir with the hndling nd mounting of hydruli omponents. Provided use Pressure reduing vlves re used to pressurise individul lmping elements or groups of lmping elements in hydruli lmping systems with redued pressure. The onneted elements must e lekge-free in stti mode. Sfety Mteril dmge Protet ginst swrf, otherwise hek vlves might not sel. Instrutions for sfe opertion Troules of funtioning The vlves 2953-1xx re designed without lekge oil port nd nnot ompenste inresing seondry pressure ( e. g. due to temperture rise, externl fores or dmge of the vlve set y swrf). Remedy: Use different type or instll in ddition pressure relief vlve. Swrf or ontmintion in the hydruli oil led to inresed wer or dmge t the guides, running surfes nd sels. The mximum operting pressure nd the dmissile flow rte of the vlve must not e exeeded. Use hydruli oil s per Roemheld dt sheet A 0.100. Pressure reduing vlves mintin the pressure t the ylinder port A (seondry pressure) more or less onstnt t vrile ut lwys higher input pressure P (primry pressure). Sujet to hnges without notie. Pge 6/8
2953-100 2953-110 3 d e f g 2 3 A Lowest possile djusting pressure p Amin. [r] - Limit urve of the lowest possile djusting pressure p Amin s funtion of the operting pressure P P Primry pressure P P [r] Operting pressue of the genertor h All figures re shemti figures. Instlltion Any mounting position of the vlves is possile. Exeption: instll type 2953-600 only in vertil position (otherwise oil loss). Connet pressure guge t seondry side (A). Return the lekge return port L depressurised t the reservoir. Threded-ody type (2953-100) Mhine with utmost ury the lotion hole, espeilly the tolerne of the ounterore of 118 (1h) nd the seling surfe (1g). Note Lurite slightly the lotion hole, ut do not lurite the Kntsel joint! Chek with your fingers if the rossings re flt nd without urr Before srewing in, turn k lok nd seling nut (1d) up to the stop. Srew in vlve ody (1) nd tighten y 70 Nm. The knife edge (1f) sels with metl to metl on the ounterore of 118 (1h, Ø24 mm). Tighten the lok nd seling nut (1d) y 60 Nm. The delivered Kntsel joint (1e) sels on the seling surfe (1g, Ø30 mm). Flnge-mounted type (2953-110) Drill holes for hydruli oil supply nd return in the fixture. Grind flnge surfe. Clen the support surfes. Remove plugs. Fsten the vlve with O-rings on the fixture. Hydruli onnetion y tues (other types) Clen the support surfes. Fsten the vlve t the flnge. Provide Hydruli the threds onnetion in the fixture. Connet hydruli lines to qulifying stndrds, py ttention to srupulous lenness! See lso Roemheld dt sheets A0.100, F9.300, F9.310 nd F9.360. Use only fittings "srewed plug B" s per DIN 3852 (ISO 1179). Do not use seling tpe, opper rings or oned fittings. Chek seling of the hydruli onnetions! Port A P L M Output (seondry side) Pressure supply (primry side) Return port (lekge oil) Pressure guge Pressure djustment Unsrew lok nut (1). Inrese relief pressure y srewing in (lokwise) the djustment srew (1). Redue the relief pressure y srewing out (ounterlokwise) the djustment srew. Tighten lok nut. Crry out some lmping nd unlmping opertions to ensure proper opertion. Mintenne Chek if the hydruli ports re tight (visul ontrol). The vlves theirselves re mintenne free. Dt sheets Types Corresponding dt sheets 2953-1xx C2.9533 2952-400 2952-500 C2.952 2952-600 C2.9532 Sujet to hnges without notie. Pge 7/8
Generl hrteristis Prt-no. 2953-100 2953-110 2953-111 2953-400 2953-500 2953-600 Fixing/ onneting type Port A, P Threded -ody Ø11 Ø16 Flnge G1/4 + Ø5 Tue Tue or front lok Tue or front lok Flnge or thred G1/4 G1/4 G1/2 G1/4 Port M G1/4 G1/4 G1/4 G1/4 Port L Mx. operting pressure (primry side) r 500 200 200 500 Rnge of djustment r 30 380 10 150 10 150 80 450 Mx. flow rte l/min 10 15 40 10 Lekge rte m³/s 0,5 2,5 k. A. Sujet to hnges without notie. Pge 8/8