SVENSK STANDARD SS-EN 1600 Handläggande organ Fastställd Utgåva Sida SVENSK MATERIAL- & MEKANSTANDARD, SMS 1998-02-20 1 1 (1+12+12) INNEHÅLLET I SVENSK STANDARD ÄR UPPHOVSRÄTTSLIGT SKYDDAT. SIS HAR COPYRIGHT PÅ SVENSK STANDARD. EFTERTRYCK UTAN TILLSTÅND ÄR FÖRBJUDET. Welding consumables Covered electrodes for manual metal arc welding of stainless and heatresisting steels Classification Tillsatsmaterial för svetsning Belagda elektroder för manuell metallbågsvetsning av rostfria och värmebeständiga stål Indelning The European Standard has the status of a Swedish Standard. This document contains the official English version of with a Swedish translation. This standard supersedes the Swedish Standards SS 14 33 01-07, SS 14 33 15-18, SS 14 33 25, SS 14 33 31 and SS 14 33 34-35. This standard has been developed in collaboration with the Swedish Welding Commission. Swedish Standards corresponding to documents referred to in this Standard are listed in "Catalogue of Swedish Standards annually issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Den europeiska Provläsningsexemplar standarden / Preview gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av med svensk översättning. Denna standard ersätter SS 14 33 01-07, SS 14 33 15-18, SS 14 33 25, SS 14 33 31 och SS 14 33 34-35. Denna standard har utarbetats i samarbete med Svetskommissionen. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som årligen ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder. ICS 25.160.20 Standarder kan beställas hos SIS som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08-610 30 00. Telefax: 08-30 77 57 Upplysningar om sakinnehållet i standarden lämnas av SMS. Telefon: 08-459 56 00. Telefax: 08-667 85 42 E-post: info@sms-standard.se Prisgrupp R Tryckt i september 1998
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 1600 August 1997 ICS 25.160.20 Descriptors: welding, manual arc welding, welding electrodes, covered electrodes, stainless steels, weld metal, filler metal, low heat resistant materials, characteristics, chemical composition, mechanical properties, classifications, symbols, mechanical tests, designation English version Welding consumables Covered electrodes for manual metal arc welding Provläsningsexemplar / Preview of stainless and heat resisting steels Classification Produits consommables pour le soudage Electrodes enrobées pour le soudage manuel à l'arc des aciers inoxydables et résistant aux températures élevées Classification Schweißzusätze Umhüllte Stabelektrodenzum Lichtbogenhandschweißen von nicht-rostenden und hitzebeständigen Stählen Einteilung This European Standard was approved by CEN on 1997-07-24. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. E
EUROPASTANDARD EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 1600 Augusti 1997 ICS 25.160.20 Nyckelord: svetsning, manuell metallbågsvetsning, svetselektroder, belagda elektroder, rostfritt stål, svetsgods, tillsatsmaterial, värmebeständiga material, fordringar, kemisk sammansättning, mekaniska egenskaper, indelning, beteckningar, mekaniska prov, beteckning Svensk version Tillsatsmaterial för svetsning Belagda elektroder för manuell metallbågsvetsning av rostfria och Provläsningsexemplar värmebeständiga / Preview stål Indelning Produits consommables pour le soudage soudage Electrodes enrobées pour le soudage manuel à l arc des aciers inoxydables et résistant aux températures élevées Classification Welding consumables Covered electrodes for manual metal arc welding of stainless and heat resisting steels Classification Schweißzusätze Umhüllte Stabelektroden zum Lichtbogenhandschweißen von nichtrostende und hitzebeständige Stählen Einteilung Denna standard är den officiella svenska versionen av För översättningen svarar SIS. Denna europastandard antogs av CEN 1997-07-24. CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall ges status som nationell standard. Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centralsekretariat eller från någon av CENs medlemmar. Denna europastandard finns i tre officiella versioner (engelsk, fransk och tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat, har samma status som de officiella versionerna. CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. Nr. Sv
Page 2 Contents Page Foreword... 2 Introduction... 2 1 Scope... 3 2 Normative references... 3 3 Classification... 4 4 Symbols and requirements... 4 4.1 Symbol for the product/process... 4 4.2 Symbol for the chemical composition of all-weld metal... 4 4.3 Symbol for type of electrode covering... 8 4.4 Symbol for weld metal recovery and type of current... 8 4.5 Symbol for welding position... Provläsningsexemplar 8 / Preview 5 Mechanical tests... 9 5.1 General... 9 5.2 Preheating and interpass temperatures... 9 5.3 Pass sequence... 9 6 Chemical analysis... 10 7 Technical delivery conditions... 10 8 Designation... 10 Annex A (informative) Description of types of electrode covering... 11 Annex B (informative) Bibliograhpy... 12 Foreword This European Standard has been prepared by Technical Committee CEN/TC 121 "Welding", the secretariat of which is held by DS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 1998, and conflicting national standards shall be withdrawn at the latest by February 1998. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Introduction This standard proposes a classification in order to designate covered electrodes in terms of the chemical composition of the all-weld metal. It should be noted that the mechanical properties of all-weld metal test specimens used to classify the electrodes will vary from those obtained in production joints because of differences in welding procedure such as electrode diameter, width of weave, welding position and material composition.
Sida 2 Innehåll Sida Förord... 2 Orientering... 2 1 Omfattning... 3 2 Bindande referenser... 3 3 Indelning... 4 4 Beteckningar och krav... 4 4.1 Beteckning för produkten/metoden... 4 4.2 Beteckning för kemisk sammansättning hos helsvetsgods...4 4.3 Beteckning för elektrodens höljetyp... 8 4.4 Beteckning för svetsgodsutbyte och strömart... 8 4.5 Beteckning för svetsläge... Provläsningsexemplar / Preview 8 5 Mekanisk provning... 9 5.1 Allmänt... 9 5.2 Förhöjd arbets- och mellansträngstemperatur... 9 5.3 Strängföljd... 9 6 Kemisk analys... 10 7 Tekniska leveransbestämmelser... 10 8 Beteckning... 10 Bilaga A (ej bindande) Beskrivning av höljetyper hos elektroder... 11 Bilaga B (ej bindande) Bibliografi... 12 Förord Denna europastandard har utarbetats av den tekniska kommittén CEN/TC 121 "Welding" med sekretariat vid DS. Denna europastandard skall ges status av nationell standard, antingen genom att publicera en identisk text eller genom ikraftsättning senast februari 1998, och motstridande nationella standarder skall dras in senast februari 1998. Enligt CEN/CENELECs interna bestämmelser anmodas följande länder att anta denna europastandard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike. Orientering Denna standard anger en indelning för att beteckna belagda elektroder med kemiska sammansättningen hos helsvetsgodset. Det bör framhållas att de mekaniska egenskaperna hos helsvetsprov som används för att indela elektroderna kommer att avvika från de som uppnås i produktionsförband på grund av skillnader i svetsprocedur som t.ex. elektroddimension, pendlingsbredd, svetsläge och materialsammansättning.
Page 3 1 Scope This standard specifies requirements for classification of covered electrodes based on the all-weld metal in the as welded or heat treated conditions for manual metal arc welding of stainless and heat resisting steels. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 759 EN 1597-1 EN 1597-3 EN 22401 EN ISO 13916 ISO 31-0:1992 Welding consumables Technical delivery conditions for welding filler metals including type of product, dimensions, Provläsningsexemplar tolerances / Preview and marking Welding consumables Test methods Part 1: Test assembly for all-weld metal test specimen in steel, nickel and nickel alloys Welding consumables Test methods Part 3: Classification testing of positional capability of welding consumables in a fillet weld Covered electrodes Determination of the efficiency, metal recovery and deposition coefficient (ISO 2401:1972) Welding Guide for measurement of preheating temperature, interpass temperature and preheat maintenance temperature (ISO 13916:1996) Quantities and units Part 0: General principles
Sida 3 1 Omfattning Standarden anger krav för indelning av belagda elektroder baserat på helsvetsgods i obehandlat tillstånd eller värmebehandlat tillstånd vid manuell metallbågsvetsning av rostfria stål och värmebeständiga stål. 2 Bindande referenser Denna europastandard införlivar genom daterad eller odaterad referens, bestämmelser från andra publikationer. Dessa bindande referenser citeras i tillämpliga delar av texten och publikationerna förtecknas här nedan. För daterade referenser gäller efterföljande tillägg och revideringar bara när de införlivas i denna europastandard genom tillägg eller revidering. För odaterade referenser gäller den senaste utgåvan av den refererade publikationen. EN 759 EN 1597-1 EN 1597-3 EN ISO 13916 EN 22401 ISO 31-0:1992 Tillsatsmaterial för svetsning Tekniska leveransbestämmelser för tillsatsmaterial för Provläsningsexemplar svetsning omfattande / Preview produkttyp, dimensioner, toleranser och märkning Tillsatsmaterial för svetsning Provningsmetoder Del 1: Prov för helsvetsprovstavar i stål, nickel och nickellegeringar Tillsatsmaterial för svetsning Provningsmetoder Del 3: Provning av lägessvetsbarhet hos svetstillsatsmaterial i en kälsvets Svetsning Mätning av förhöjd arbetstemperatur, mellansträngstemperatur och arbetstemperatur under svetsning (ISO 13916: 1996) Belagda elektroder Bestämning av nettoutbyte, bruttoutbyte och smälttal (ISO 2401:1972) Quantities and units Part 0: General principles (Mängder och enheter Del 0: Allmänna principer)
Page 4 3 Classification The classification includes all-weld metal properties obtained with a covered electrode as given below. The classification is based on the electrode diameter 4 mm with the exception of the testing for welding position which is based on diameter 3,2 mm. The classification is divided into five parts: 1) the first part gives a symbol indicating the product/process to be identified; 2) the second part gives a symbol indicating the chemical composition of all-weld metal; 3) the third part gives a symbol indicating the type of electrode covering; 4) the fourth part gives a symbol indicating the weld metal recovery and the type of current; 5) the fifth part gives a symbol indicating the welding position. In order to facilitate the use of this standard, the classification is split into two sections: a) Compulsory section This section includes the symbols for the type of product, the chemical composition and the type of covering, i.e. the symbols defined in 4.1, 4.2 and 4.3; b) Optional section This section includes the symbols for the weld metal recovery, the type of current and the welding positions for which the electrode is suitable, i.e. the symbols defined in 4.4 and 4.5. The full designation (see clause 8) shall be used on packages and in the manufacturer's literature and data sheets. Provläsningsexemplar / Preview 4 Symbols and requirements 4.1 Symbol for the product/process The symbol for the covered electrode used in the manual metal arc welding process shall be the letter E. 4.2 Symbol for the chemical composition of all-weld metal The symbol in table 1 indicates the chemical composition of all-weld metal determined in accordance with clause 6. The all-weld metal obtained with the covered electrodes in table 1 in accordance with clause 5 shall also fulfil the mechanical property requirements specified in table 2.
Sida 4 3 Indelning Indelningen omfattar egenskaper hos helsvetsgods som erhållits med en belagd elektrod enligt nedan. Indelningen baseras på elektroddiameter 4 mm med undantag för beteckningen av svetsläge som baseras på diameter 3,2 mm.. Indelningen av ett svetsgods uppdelas i fem delar: 1) den första delen ger en beteckning som anger produkten/metoden som avses 2) den andra delen ger en beteckning som anger den kemiska sammansättningen hos helsvetsgodset 3) den tredje delen ger en beteckning som anger elektrodens höljetyp 4) den fjärde delen ger en beteckning som anger svetsgodsutbyte och strömart 5) den femte delen ger en beteckning som anger svetsläge I avsikt att främja användningen av denna standard är indelningen uppdelad i Provläsningsexemplar / Preview två grupper: a) Obligatorisk grupp Denna grupp omfattar beteckningar för produkttyp, kemisk sammansättning och höljetyp, d.v.s. de beteckningar som definieras i 4.1, 4.2 och 4.3. b) Frivillig grupp Denna grupp omfattar beteckningar för svetsgodsutbyte, strömart och svetslägen där elektroden är lämplig, d.v.s. de beteckningar som definieras i 4.4 och 4.5. Hela beteckningen (se 8) skall användas på förpackningar och i tillverkarens litteratur och produktblad. 4 Beteckningar och krav 4.1 Beteckning för produkten/metoden Beteckningen för en belagd elektrod för manuell metallbågsvetsning är bokstaven E. 4.2 Beteckning för kemisk sammansättning hos helsvetsgods Beteckningen i tabell 1 anger kemiska sammansättningen hos helsvetsgods, fastställd enligt avsnitt 6. Helsvetsgods med belagda elektroder i tabell 1 som erhållits enligt avsnitt 5 skall även innehålla de fordringar på mekaniska egenskaper som anges i tabell 2.
Alloy symbol (continued) Chemical composition in % (m/m) 1)2)3) C Si Mn P 4) S 4) Cr Ni 5) Mo 5) Other elements 5) Martensitic/ Ferritic 13 0,12 1,0 1,5 0,030 0,025 11,0 to 14,0 13 4 0,06 1,0 1,5 0,030 0,025 11,0 to 14,5 3,0 to 5,0 0,4 to 1,0 17 0,12 1,0 1,5 0,030 0,025 16,0 to 18,0 Austenitic 19 9 0,08 1,2 2,0 0,030 0,025 18,0 to 21,0 9,0 to 11,0 19 9 L 0,04 1,2 2,0 0,030 0,025 18,0 to 21,0 9,0 to 11,0 19 9 Nb 0,08 1,2 2,0 0,030 0,025 18,0 to 21,0 9,0 to 11,0 Nb 6) 19 12 2 0,08 1,2 2,0 0,030 0,025 17,0 to 20,0 10,0 to 13,0 2,0 to 3,0 19 12 3 L 0,04 1,2 2,0 0,030 0,025 17,0 to 20,0 10,0 to 13,0 2,5 to 3,0 19 12 3 Nb 0,08 1,2 2,0 0,030 0,025 17,0 to 20,0 10,0 to 13,0 2,5 to 3,0 Nb 6) 19 13 4 N L 7) 0,04 1,2 1,0 to 5,0 0,030 0,025 17,0 to 20,0 12,0 to 15,0 3,0 to 4,5 N 0,20 Austenitic-Ferritic. High corrosion resistance 22 9 3 N L 8) 0,04 1,2 2,5 0,030 0,025 21,0 to 24,0 7,5 to 10,5 2,5 to 4,0 N 0,08 to 0,20 25 7 2 N L 0,04 1,2 2,0 0,035 0,025 24,0 to 28,0 6,0 to 8,0 1,0 to 3,0 N 0,20 25 9 3 Cu N L 8) 0,04 1,2 2,5 0,030 0,025 24,0 to 27,0 7,5 to 10,5 2,5 to 4,0 N 0,10 to 0,25; Cu 1,5 to 3,5 25 9 4 N L 8) 0,04 1,2 2,5 0,030 0,025 24,0 to 27,0 8,0 to 10,5 2,5 to 4,5 N 0,20 to 0,30; Cu 1,5; W 1,0 Fully Austenitic. High corrosion resistance 18 15 3 L 7) 0,04 1,2 1,0 to 4,0 0,030 0,025 16,5 to 19,5 14,0 to 17,0 2,5 to 3,5 18 16 5 N L 4) 0,04 1,2 1,0 to 4,0 0,035 0,025 17,0 to 20,0 15,5 to 19,0 3,5 to 5,0 N 0,20 20 25 5 Cu N L 7) 0,04 1,2 1,0 to 4,0 0,030 0,025 19,0 to 22,0 24,0 to 27,0 4,0 to 7,0 Cu 1,0 to 2,0; N 0,25 20 16 3 Mn N L 7) 0,04 1,2 5,0 to 8,0 0,035 0,025 18,0 to 21,0 15,0 to 18,0 2,5 to 3,5 N 0,20 25 22 2 N L 7) 0,04 1,2 1,0 to 5,0 0,030 0,025 24,0 to 27,0 20,0 to 23,0 2,0 to 3,0 N 0,20 27 31 4 Cu L 7) 0,04 1,2 2,5 0,030 0,025 26,0 to 29,0 30,0 to 33,0 3,0 to 4,5 Cu 0,6 to 1,5 Special types 18 8 Mn 7) 0,20 1,2 4,5 to 7,5 0,035 0,025 17,0 to 20,0 7,0 to 10,0 18 9 Mn Mo 0,04 to 0,14 1,2 3,0 to 5,0 0,035 0,025 18,0 to 21,5 9,0 to 11,0 0,5 to 1,5 20 10 3 0,10 1,2 2,5 0,030 0,025 18,0 to 21,0 9,0 to 12,0 1,5 to 3,5 23 12 L 0,04 1,2 2,5 0,030 0,025 22,0 to 25,0 11,0 to 14,0 23 12 Nb 0,10 1,2 2,5 0,030 0,025 22,0 to 25,0 11,0 to 14,0 Nb 6) 23 12 2 L 0,04 1,2 2,5 0,030 0,025 22,0 to 25,0 11,0 to 14,0 2,0 to 3,0 29 9 0,15 1,2 2,5 0,035 0,025 27,0 to 31,0 8,0 to 12,0 Page 5 Provläsningsexemplar / Preview Table 1: Symbol for chemical composition of all-weld metal
Sida 5 Provläsningsexemplar / Preview Tabell 1: Beteckning för kemisk sammansättning hos svetsgods Beteckning fortsättning Kemisk sammansättning % (m/m) 1)2)3) C Si Mn P 4) S 4) Cr Ni 5) Mo 5) Övriga grundämnen 5) Martensitisk/ Ferritisk 13 0,12 1,0 1,5 0,030 0,025 11,0 14,0 13 4 0,06 1,0 1,5 0,030 0,025 11,0 14,5 3,0 5,0 0,4 1,0 17 0,12 1,0 1,5 0,030 0,025 16,0 18,0 Austenitisk 19 9 0,08 1,2 2,0 0,030 0,025 18,0 21,0 9,0 11,0 19 9 L 0,04 1,2 2,0 0,030 0,025 18,0 21,0 9,0 11,0 19 9 Nb 0,08 1,2 2,0 0,030 0,025 18,0 21,0 9,0 11,0 Nb 6) 19 12 2 0,08 1,2 2,0 0,030 0,025 17,0 20,0 10,0 13,0 2,0 3,0 19 12 3 L 0,04 1,2 2,0 0,030 0,025 17,0 20,0 10,0 13,0 2,5 3,0 19 12 3 Nb 0,08 1,2 2,0 0,030 0,025 17,0 20,0 10,0 13,0 2,5 3,0 Nb 6) 19 13 4 N L 7) 0,04 1,2 1,0 5,0 0,030 0,025 17,0 20,0 12,0 15,0 3,0 4,5 N 0,20 Austenitisk-Ferritisk. Hög korrosionsbeständighet 22 9 3 N L 8) 0,04 1,2 2,5 0,030 0,025 21,0 24,0 7,5 10,5 2,5 4,0 N 0,08 0,20 25 7 2 N L 0,04 1,2 2,0 0,035 0,025 24,0 28,0 6,0 8,0 1,0 3,0 N 0,20 25 9 3 Cu N L 8) 0,04 1,2 2,5 0,030 0,025 24,0 27,0 7,5 10,5 2,5 4,0 N 0,10 0,25; Cu 1,5 3,5 25 9 4 N L 8) 0,04 1,2 2,5 0,030 0,025 24,0 27,0 8,0 10,5 2,5 4,5 N 0,20 0,30; Cu 1,5; W 1,0 Helaustenitisk. Hög korrosionsbeständighet 18 15 3 L 7) 0,04 1,2 1,0 4,0 0,030 0,025 16,5 19,5 14,0 17,0 2,5 3,5 18 16 5 N L 4) 0,04 1,2 1,0 4,0 0,035 0,025 17,0 20,0 15,5 19,0 3,5 5,0 N 0,20 20 25 5 Cu N L 7) 0,04 1,2 1,0 4,0 0,030 0,025 19,0 22,0 24,0 27,0 4,0 7,0 Cu 1,0 2,0; N 0,25 20 16 3 Mn N L 7) 0,04 1,2 5,0 8,0 0,035 0,025 18,0 21,0 15,0 18,0 2,5 3,5 N 0,20 25 22 2 N L 7) 0,04 1,2 1,0 5,0 0,030 0,025 24,0 27,0 20,0 23,0 2,0 3,0 N 0,20 27 31 4 Cu L 7) 0,04 1,2 2,5 0,030 0,025 26,0 29,0 30,0 33,0 3,0 4,5 Cu 0,6 1,5 Specialtyper 18 8 Mn 7) 0,20 1,2 4,5 7,5 0,035 0,025 17,0 20,0 7,0 10,0 18 9 Mn Mo 0,04 0,14 1,2 3,0 5,0 0,035 0,025 18,0 21,5 9,0 11,0 0,5 1,5 20 10 3 0,10 1,2 2,5 0,030 0,025 18,0 21,0 9,0 12,0 1,5 3,5 23 12 L 0,04 1,2 2,5 0,030 0,025 22,0 25,0 11,0 14,0 23 12 Nb 0,10 1,2 2,5 0,030 0,025 22,0 25,0 11,0 14,0 Nb 6) 23 12 2 L 0,04 1,2 2,5 0,030 0,025 22,0 25,0 11,0 14,0 2,0 3,0 29 9 0,15 1,2 2,5 0,035 0,025 27,0 31,0 8,0 12,0