Manual STEF Brand
Montering... 8 Elkopplingar... 9 Kopplingsschema... 11 Service... 12 Installation... Electrical w iring... 15 Wiring diagram... 17 Servicing... 18 Spare parts... 26 Spare parts... 27 CE... 28 OBS! Bryt ström till fläkten ca. 2 minuter före serviceåtgärder. NB. The power roof fan must be isolated from the mains power supply appr. 2 minutes before starting any maintenance work. 2
Takfläkt STEF Montering Lyftögla, storlek 6 och 7 Gångjärn Tätning Säkerhetsbrytare (tillbehör) Fig. 1 Montering på takgenomföring BOGA 1. Montera medlevererade tätningen på takgenomföringens övre kant enligt figur 1. 2. Lyft takfläkt STEF på takgenomföringen. Vid behov använd medföljande lyftöglor. Figur 1. Observera att: bottenplattan kommer över takgenomföringens kant. Skada inte tätningen. säkerhetsbrytaren och kabelgenomföringen på takgenomföringen kommer på samma sida, vilket avgör gångjärnsläget. Figur 1. 3. Fäst takfläkten via bottenplattan i gängade hål i takgenomföringens kant med fyra M8x35 skruvar Vikter Storlek 1 2 3 4 5 6 7 Vikt, kg STEF 31 31 45 50 66 116 9 8
Elkopplingar Takfläkt STEF Elkopplingar Kopplingsschemor på sida 5-6. Takfläkt levererad med fabrikskopplad säkerhetsbrytare SAFE 1. Montera säkerhetsbrytare på önskad plats, observera gångjärnens riktning 2. Öppna säkerhetsbrytarens lock 3. Dra kabeln för matningsströmmen genom kabelgenomföringen i säkerhetsbrytaren. Reservera tillräckligt med kabel så att fläktdelen kan öppnas för service. 4. Utför kopplingen och stäng säkerhetsbrytarens lock 5. Kontrollera säkerhetsbrytarens fuktion 6. Vid igångskörning av fläkten kontrollera fläkthjulets rotationsriktning FO-drift STEF takfläktar med enhastighets-trefasmotorer kan köras med frekvensomriktare. Min. drift-frekvens är 20 Hz och max. driftfrekvens 50 Hz, eventuella högre driftfrekvenser är angivna i STEF-katalog. Rätt till förändringar förbehållas. 9
Kopplingsschema Takfläkt STEF Trefasmotor, direkt elinkoppling Enhastighetsmotor, Y-koppling Rätt till förändringar förbehållas. 11
Takfläkt STE F S ervice Skötsel Takfläkten kräver vid normal drift inte någon skötsel. Vid drift i nedsmutsande miljö, såsom frånluftsfläkt i kök, krävs rengöring av eventuella smutsavlagringar i fläkthjul och kåpa. Ta även hänsyn de lokala bestämmelserna om luftbehandlingsanläggningens rengöring. Skötsel av takfläkt i gnistsäkert utförande fläkthjul och motor måste kollas och vid behov rengöras åtminstone en gång om året för att garantera problemfri drift. Rengöring av fläkthjul, kåpa och kanal 1. Koppla bort takfläkten från elnätet med säkerhetsbrytaren. 2. Öppna fästskruvarna ca. 10 mm så, att fläktdelen kan fällas upp med hjälp av gångjärnen. Vindhaken (1 eller 2 st beroende på fläktstorlek) låser fläktdelen automatiskt i ändläge. Figur 3. 3. Se till, att vindhaken har låst sig ordentligt och fästena i takfläktens bottenplatta och monteringsram är i god kondition. 4. Utför rengöringsarbetet. Även fläktens ljudisolerade kåpa kan rengöras eftersom isoleringen är skyddad med perforerad plåt. 5. När servicen är utförd, frigör uppfällningsstödet genom att trycka på låsspaken (se figur 3) och sänk fläktdelen tillbaka på sin plats. Spänn fästskruvarna. Fläktkåpan kan rengöras även uppifrån genom att öppna takgallret. Byte av motor och fläkthjul 1. Koppla bort takfläkten från elnätet med säkerhetsbrytaren. 2. Fäll upp fläktdelen som vid rengöring, se punkterna 2 och 3 ovan. 3. Öppna fläkthjulets ändplatta och dra fläkthjulet bort från motoraxeln. Änvänd vid behov avdragare. Obs! Det lönar sig att täcka den öppna skorstenen före demonteringen så att inte delar och verktyg av misstag faller ner i skorstenen. 4. Sänk ner fläktdelen, ta bort takgaller (figur 4) lösgör elkablarna från kopplingsdosan samt motorn från motorhyllan. 5. Montera ny motor och fläkthjul i motsatt ordning. 6. Stäng takfläkten, starta och lyssna att inga ovanliga ljud hörs från takfläkten. Skrotning av produkten 1. Fläkten innehåller elmotor och eventuellt frekvensomriktare, tryckregulator och andra elkomponenter. Alla elektriska komponenter måste levereras till special återvinning för skrotning. 2. Stålmaterial kan återanvändas 3. Fläkten innehåller endast marginella mängder av plastmaterial. Plastmaterial är återanvändbar. Brandgasutförande Vid skötsel av brandgasutförande måste även lokala föreskrifter följas. Låsspak Vindhake Fästskruv Fig. 3 Fig. 4 12
ROOFMASTER STEF and STOF Installation The STEF and STOF roof fans are used as exhaust fans in ventilation systems. The roof fan can be mounted either on a BOGA roof duct, STEZ-01 flat roof socket or STEZ-07 sound attenuator or on a chimney built at site with help of MORA or STEZ-03 mounting frame. The fan section is supported by hinges on one edge of the base plate and can be raised and locked in fully open position for cleaning. Lifting lugs, STEF 6 and 7 Hinges Sealing Safety switch (optional) Fig. 1 To mount the STEF on the BOGA roof duct 1. Fit the sealing strip to the top edge of the roof duct as shown in Figure 1. 2. Lift the STEF or STOF roof fan onto the roof duct. Use the lifting lugs for the larger sizes if necessary. See Figure 1. Make sure that: the fan base plate is seated over the edges of the roof duct. Do not damage the sealing strip. the safety switch and the cable gland in the roof duct are on the same side. This determines the position of the hinges. See Figure 1. 3. Secure the roof fan via its base plate to the roof duct flanges (tapped holes) using the four M8x35 screws supplied with the fan.
Electrical wiring ROOFMASTER STEF and STOF Weights Size 1 2 3 4 5 6 7 002 005 Weight, kg STEF 31 31 45 50 66 116 9 STOF 5,6 5,8 Frequency converter drive STEF roof fans with single speed three-phase motors can be driven with frequency converters. The min. frequency is is 20 Hz. Max. frequency is 50Hz, for possibly higher max. frequencies please refer to the STEF-catalogue. Electrical wiring (To be carried out by an authorised electrician). The wiring diagrams are on the following page. Roof fan STEF supplied with factory-wired safety switch SAFE. 1. Mount the safety switch please note the position of the hinges. 2. Open the safety switch cover. 3. Run the power supply cable through the cable gland of the safety switch. Adjust the length of the cable so that sufficient slack will be available for opening the fan for servicing. 4. Wire the connections and close the safety switch. 5. Check to make sure that the safety switch functions properly. 6. When commissioning the fan make sure that the impeller is rotating to the right direction. We reserve the right to make changes 15
Wiring diagram ROOFMASTER STEF Three-phase, single speed motor star coupled We reserve the right to make changes 17
R OOFMASTE R STE F S ervicing Maintenance Under normal operating conditions the roof fan does not require any other maintenance except for checking the motor bearings. If the fan is used for applications where exhaust air contains impurities (for example kitchen) the impeller and the fan casing must be cleaned regularly. All local regulations and norms must be complied with. To clean the impeller, casing and duct 1. Switch off the roof fan from the safety switch. 2. Back off the fixing screws appr. 10 mm so that the fan section can be raised on its hinges. The stay rod (1 or 2 stay rods depending on the fan size) locks the fan section automatically in the fully open position as shown in the Figure 3. 3. Make sure that the stay rod has become locked properly in the open position and that the mounting of the fan base plate (and possible mounting frame) is in good condition. 4. Clean as required. The sound insulated fan casing surfaces can also be cleaned since the insulation is protected. 5. On having completed the maintenance work release the stay rod by depressing the locking lever (see Figure 3) and lower the fan section back to its initial position. Re-tighten the fixing screws. The fan casing can also be cleaned from the top after removing the protective screen. 3. Open the back plate of the impeller and prise the impeller off the motor shaft. If necessary use an extractor. Note! It is advisable to cover the the chimney opening before dismantling the impeller so that parts or tools will not fall down the chimney. 4. Lowe the fan section and remove the protective screen (Fig. 4), loose the motor cable and remove the motor from the motor bracket. 5. Mount a new motor and fan impeller in the reverse order. 6. Close the roof fan, turn it on and check that no abnormal noise or vibrations occur and that the impeller rotates to the right direction. Maintenance of smoke extraction version Follow the instructions above. In the maintenance of smoke extraction version the local regulations and norms must also be followed. Scrapping the fan Sort the materials in accordance with national environmental regulations and deliver the materials either for recycling or proper disposal. Lockinh lever Stay rod Fixing screw Fig. 3 To change the motor and the impeller 1. Switch off the roof fan from the safety switch. 2. Open the fan section as described in previous section Maintenance, pos. 2 and 3. Fig. 4 18
26 ROOFMASTER STEF and STOF Spare parts Spare parts Reservdelar Varaosat Varuosad Ersatzteile Reservedele STEF-1-104-c-1-e STEF-1-004-c-1-e STEF-1-406-c-1-e STEF-1-408-c-1-e STEF-2-104-c-1-e STEF-2-004-c-1-e STEF-2-006-c-1-e STEF-2-406-c-1-e STEF-2-408-c-1-e STEF-3-104-c-1-e STEF-3-004-c-1-e STEF-3-006-c-1-e STEF-3-406-c-1-e STEF-3-408-c-1-e STEF-4-104-c-1-e STEF-4-004-c-1-e STEF-4-406-c-1-e STEF-4-408-c-1-e STEF-4-006-c-1-e STEF-5-004-c-1-e STEF-5-006-c-1-e STEF-5-408-c-1-e STEF-6-006-c-1-e STEF-6-612-c-1-e STEF-6-812-c-1-e STEF-7-006-c-1-e STEF-7-008-c-1-e STEF-7-612-c-1-e STEF-7-812-c-1-e 28 28 63 63 90 90 90 100 100 132 132 132 132 Fan code Fläktkod Puhallin Ventilaatori kood Ventilator Ventilatorkode STEF-99-02-01 STEF-99-02-37 STEF-99-02-39 STEF-99-02- STEF-99-02-04 STEF-99-02-37 STEF-99-02-40 STEF-99-02-39 STEF-99-02- STEF-99-02-08 STEF-99-02- STEF-99-02-40 STEF-99-02-15 STEF-99-02-16 STEF-99-02-13 STEF-99-02-32 STEF-99-02-15 STEF-99-02-16 STEF-99-02-33 STEF-99-02- STEF-99-02-20 STEF-99-02-35 STEF-99-02-23 STEF-99-02- STEF-99-02-25 STEF-99-02-26 STEF-99-02-27 STEF-99-02-28 STEF-99-02-29 d mm IEC Spare parts code Reservdelskod Varaosakoodi Moottori Varuosa kood Mootor Ersatzteilkode Reservedelskode STEF-1-104-c-1-e STEF-1-004-c-1-e STEF-1-406-c-1-e STEF-1-408-c-1-e STEF-2-104-c-1-e STEF-2-004-c-1-e STEF-2-006-c-1-e STEF-2-406-c-1-e STEF-2-408-c-1-e STEF-3-104-c-1-e STEF-3-004-c-1-e STEF-3-006-c-1-e STEF-3-406-c-1-e STEF-3-408-c-1-e STEF-4-104-c-1-e STEF-4-004-c-1-e STEF-4-406-c-1-e STEF-4-408-c-1-e STEF-4-006-c-1-e STEF-5-004-c-1-e STEF-5-006-c-1-e STEF-5-408-c-1-e STEF-6-006-c-1-e STEF-6-612-c-1-e STEF-6-812-c-1-e STEF-7-006-c-1-e STEF-7-008-c-1-e STEF-7-612-c-1-e STEF-7-812-c-1-e 28 28 5 5 5 5 4 4 4 600 600 600 744 744 744 744 STEF-99-01-01 STEF-99-01-01 STEF-99-01-01 STEF-99-01-01 STEF-99-01-02 STEF-99-01-02 STEF-99-01-02 STEF-99-01-02 STEF-99-01-02 STEF-99-01-03 STEF-99-01-04 STEF-99-01-03 STEF-99-01-04 STEF-99-01-04 STEF-99-01-05 STEF-99-01-05 STEF-99-01-05 STEF-99-01-05 STEF-99-01-06 STEF-99-01-07 STEF-99-01-08 STEF-99-01-07 STEF-99-01-09 STEF-99-01-10 STEF-99-01-10 STEF-99-01-11 STEF-99-01-11 STEF-99-01-11 STEF-99-01-11 Fan code Fläktkod Puhallin Ventilaatori kood Ventilator Ventilatorkode d mm D Spare parts code Fan Impeller Reservdelskod Fläkthjul Varaosakoodi Puhallinpyörä Varuosa kood Tiivik Ersatzteilkode Laufrad Reservedelskode Ventilatorhjul e = generation 5
Spare parts ROOFMASTER STEF and STOF Spare parts Reservdelar Varaosat (savunpoisto) Varuosad Ersatzteile Reservedele Fan code Fläktkod Puhallin Ventilaatori kood Ventilator Ventilatorkode Spare parts code Fan Impeller Reservdelskod Fläkthjul Varaosakoodi Puhallinpyörä Varuosa kood Tiivik Ersatzteilkode Laufrad Reservedelskode Ventilatorhjul d mm D Fan code Fläktkod Puhallin Ventilaatori kood Ventilator Ventilatorkode Spare parts code Reservdelskod Varaosakoodi Moottori Varuosa kood Mootor Ersatzteilkode Reservedelskode d mm IEC STEF-1-004-c-6-e STEF-99-03-01 5 STEF-1-004-c-6-e STEF-99-04-01 63 STEF-2-004-c-6-e STEF-2-006-c-6-e STEF-99-03-02 STEF-99-03-02 STEF-2-004-c-6-e STEF-2-006-c-6-e STEF-99-04-01 STEF-99-04-04 63 STEF-3-004-c-6-e STEF-3-006-c-6-e STEF-99-03-04 STEF-99-03-03 STEF-3-004-c-6-e STEF-3-006-c-6-e STEF-99-04-05 STEF-99-04-04 STEF-4-004-c-6-e STEF-4-006-c-6-e STEF-99-03-06 STEF-99-03-05 STEF-4-004-c-6-e STEF-4-006-c-6-e STEF-99-04-08 STEF-99-04-09 STEF-5-004-c-6-e STEF-5-006-c-6-e STEF-99-03-08 STEF-99-03-07 4 4 STEF-5-004-c-6-e STEF-5-006-c-6-e STEF-99-04-10 STEF-99-04-11 90 STEF-6-006-c-6-e STEF-99-03-09 600 STEF-6-006-c-6-e STEF-99-04-13 90 STEF-7-006-c-6-e STEF-99-03-11 744 STEF-7-006-c-6-e STEF-99-04-15 132 e = 3 We reserve the right to make changes 27
ROOFMASTER STEF 28 CE