Information, Monterings- och bruksanvisning Information, Installation and Operating Instructions BMW X3 SUV (E83) 2004» Passar även M-paket & Sport e20*94/20 Alexo Sweden - The Original Towbar ATS: 612-009
Generella riktlinjer Dragkroken skall monteras i enlighet med monteringsanvisningarna. Montering bör endast ske av behörig mekaniker. Monteringen sker på egen risk och skador som uppkommer på grund av monterad dragkrok kan ej belastas tillverkaren. Nationella direktiv beträffande monteringen ska beaktas. Det är förbjudet att göra ändringar eller ombyggnader på dragkroken. Detta leder till att typgodkännandet dras in. Tag bort isoleringsmassan eller underplåtens skyddsbeläggning (om sådan finns) från bilen i området kring dragkrokens anläggningsytor. Dragkroken är avsedd för att dra släpvagnar, som är utrustade med dragkulskopplingar, samt för lasthållare (exempelvis fastsättning av cykelställ), som är tillåtna för montering på dragkroken. All annan användning är förbjuden. Vid fordon med parkeringshjälp kan felaktiga funktioner förekomma efter att draganordningen monterats, eftersom det finns risk för att vissa delar (dragkulstång, kopplingskula) ligger inom sensorernas avkänningsområde. I sådana fall bör avkänningsområdet anpassas eller parkeringshjälpen avaktiveras. Om draganordningar med avtagbara eller svängbara kulstänger används, kan inga felaktiga funktioner förväntas efter att dragkulstången har tagits ut ur driftläget. Dragkroken ställer högre krav på kylsystemet. För eventuellt nödvändiga ombyggnadsåtgärder på kylsystemet kontaktas bilverkstaden. Guidelines The towbar should be installed in accordance with the installation instructions. Installation should be carried out by an experienced mechanic. All fitting is performed under own risk and manufacturer cannot be held responsible for any damage caused by fitting this towbar. Always observe national guidelines concerning official approval of extensions. Any alteration and/or conversion of the tow bar is prohibited and will result in the cancellation of the type approval. Remove insulating compound and/or underseal (if existing) from around the tow bar s mating surfaces on the vehicle. The tow bar is designed for towing trailers fitted with ball couplings and for use with load bearing implements approved for attachment to the tow bar. Any use other than the one specified is prohibited. If vehicles are fitted with a Parking Distance Control (PDC) system malfunctioning of the system can occur after tow bar installation since the parts (ball bar, ball coupling) could be located in the detection area of the sensors. In this case, the detection area should be readjusted or the PDC deactivated. Malfunctioning is not expected when using tow bars with detachable or pivoted ball bars if the ball bar is removed from its operating position. The towing hitch makes increased demands on the cooling system. Inquire at your contracted garage regarding any necessary reconstruction measures on the cooling system.
Material 2 x (M12x70-8,8) Viktigt! Se till att samtliga delar finns med innan installationen påbörjas. 6 x (M12) 2 x (M12) 4 x (Ø36) 6 x (M12) Important! Make sure that all parts are available prior to starting the fitting procedure.
Monteringsanvisningar Illustrationer finns på kommande sidor Demontera bakspoilern. Demontera skyddskåpan i bakspoilern, denna kasseras. Placera dragkroksbalken mot bilens chassie och fäst med M12 muttrar (point 1). Montera bakspoilern. Montera dragkroken och kontaktdosan till elsatsen med bultar M12x70 8.8 (point 2). Momentdrag samtliga bultar enligt tabellen på manualens baksida. Installation Instructions Illustrations found on the following pages Unscrew the bumper. Unscrew the reinforcement of the bumper (it will not be used any more). Put the main bar A to the rear belt and screw with nuts M12 through the holes (point 1). Assemble the bumper. Fix the ball and electric plate with bolts M12x70 8.8 (point 2). Connect the electric wires. Tighten all the bolts according to the torque setting- see the table.
Anteckningar
Installation av Elsats Vid installation av elkabelsats skall extra försiktighet tagas vid fordon utrustade med CANBus och check-bulb kontroll. Vid installation av elsats krävs i dessa fall inkoppling av ett avancerat relä, alternativt inkoppling av bilspecifik elsats. Vid inkoppling av CANBus control enhet såsom GDS-X7 ger nedanstående diagram exempel på inkoppling. Färger kan variera och vid osäkerhet skall multimeter användas. Fitting of Electric kit When installing towbar electrics extra caution must be taken when fitting on modern cars with CAN Bus systems. In these cases an advanced can bus control relay module must be installed or the fitting of an vehicle specific electrical kit. When connection of the GDS-X7 system the diagram below specifies which signal cables should be used. Colours may vary, when uncertain use a voltmeter. Notering BMW X3 E83 2004» Bromsljus och bakljus delar kabel. Koppla endast röd kabel från GDS-X7 Multiplexa kablar. GDS-X7 kabel Enhet Kopplas till Alternativ koppling Strömkabel +12v +12v uttag (cigg + (plus) polen på bilens startbatteri (tjock svart uttag) Vit kabel Jord Jordad kontakt eller jordat uttag - (minus) polen på bilens startbatteri GDS-X7 Lampa Kopplas till Alternativ koppling Inkoppling kabelfärg kabel Gul Vänster blinkers Blå/grön Blå Dimbakljus Gul/svart Ej krav Grön Höger blinkers Blå/brun Brun Höger baklampa Grå/gul Koppla inte in. Röd Bromslampa Svart/blå Svart Vänster Grå/lila Koppla inte in. baklampa Grå Backljus Blå/gul Ej krav
Approval Coupling class: A50-X e20*94/20*0943*00 M8 M10 M12 M14 M16 Nm 25 55 85 135 200 0 km 1000 km (C) kg (T) kg g = 9,81 m/s 2 T= 2000 kg S= 80 kg D= 10,85 kn Alexo Towbars Sweden www.alexo.se info@alexo.se Made by IHP Official distributor Sweden: BilX Nordic AB Industrivägen 23, SE-302 41 Halmstad, SWEDEN tel: +46 (0) 35 221575 www.bilx.se