FD50H SLIDING DOOR SYSTEM Installation Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand for future reference. ABOUT THE PRODUCT This product is a parts set for an overlay indoor sliding door system. The door closes in a soft motion steps; first slow, then fast, and opens with a 1 step soft motion. Easy door installation and adjustment. SPECIFICATIONS Max. Door height Max. Door width Max. Door weight 1 The closing speed of the soft closing type door may change due to ambient temperature, operating method or installation quality. Recommended ambient temperature range is 5 to 40 C. 1 If a light weight door is applied, you may feel the resistance of the soft closer when opening the door. FOR YOUR SAFE WORK AND CORRECT INSTALLATION Meaning of symbols Warning Caution Prohibited Required WARNING: If not followed, death or serious injury may result. This (sliding door system) should be installed by a qualified person. If the system is not installed correctly, the door will not operate smoothly, and may cause injury. It is necessary to manufacture the frame with sufficient strength so that it endures the weight of the door and any impact upon opening/closing the door. Only use designated screws and ensure that they are fastened firmly. A frame with poor strength or loose screws might result in the door falling and causing injury. Do not try to use this product for anything other than its original purpose. Do not use any part for applications outside of its specification. Do not disassemble nor modify any parts other than those described in this document. Caution: If not followed injury or damage may result. Make sure to follow the designated dimensions, specifications, and horizontal/vertical angles. Make sure that the frame is not warped, since it may affect the movement of the door. If cutting any parts, make sure to remove any burrs before installation. Also check the upper track for any left-over burrs or scraps and remove these. This product is a part for architectural fittings. After installation, make sure to test the finished product thoroughly to ensure that it is well-functioning and safe. Please inform the end user about general precautions and safety to prevent improper use. Make sure to check the screws for slack at regular intervals (one month from first usage, half a year, and then one time every year is recommended). 1
COMPONENT PARTS Name Upper track Side cover Stopper plate Screw for stopper Screw & nut Soft Closer plate for trigger Upper roller Item No. Hole pitch: Pitch end: mm Item Countersunk head screw Screws for stopper plate are attached to above. Countersunk head tapping screw 4 40 ( pcs/set) Pan headtapping screw Countersunk head tapping 4 pcs Countersunk head screw pcs Pan headtapping screw Nut M4 pcs Single sliding 1 pc 1 ea pcs pcs 1 pc 1 pc Name Bumper block Floor guide Door stopper Door guide track Item No. Item Bind head tapping screw 5 pcs Pan head tapping Single sliding pcs 1pc pcs 1 pc Hole pitch: 50 mm Countersunk head Cover cap ACCESSORYSpanner are not needed Countersunk head tapping 61.6 46.5 7.5 3.6 36 Track length 15 17 50 1 40 Leading Hole pitch 300 DW41 5.69 CSK [DW414] edge 50 7 7 18 6 5.69 CSK 1 7 7 7 9 40 18 3 36 9 5 8 6 1 3 9 8 3 8 15 (.5) 6 When using HH-P135 recessed pull DH13 (7) 13.5 1.8 6.5 35.5 15 34.6 9 Door height DH 8 4 Door close Door width DW Door open Track length 16.5 0 48 Trailing edge Door open 15 8 17 11 1 9 41 64 5 3 18 11 dimensions 16 15 3 47.5 1 3 45² When ( is used Cover cap Option 47 Option 17 Door guide track Option 15
ASSEMBLY Cutting Take care of the direction of upper track (leading edge, trailing edge). TriggerBumper block 4 Door open 18 DW41 50 4 40 1 4 Trailing edge 4.5 5.69 CSK Cut end Track length 5.69 CSK Track length Preparation of mounting parts Recessed roller: Separate main unit from casing. 4 Door close 1 4 Leading edge 06 50 4 18 40 4.5 4.5 Installing Casing 4.5 Pull out casing Main unit Pull up lever Casing If the is wrong, pull back the trigger catcher to OK Correct set Trigger catcher Red colored part Correct set 6 Trigger catcher Red colored part Incorrect set 3
Insert the parts in order from to with care of direction. Remove any dirt or aluminum chips from the track. Fasten bumper blocks temporarily to prevent the inserted parts from falling. Upper track Bumper block Upper roller Bumper block Trailing edge Leading edge Verify that the upper track is set horizontally before fastening. Remove any dirt or aluminum chips from the track. Countersunk tapping screw 4x40 (provided) Installing Trigger Fasten triggers to 1the hole made during procedure 1 with the provided nuts. M4 (accessory) M4 (accessory) Bumper block Pan head screw 416 Trigger Countersunk head screw 4(D6) 4
Assembling Side Cover Provided screw Stopper plate Side cover Fixing Floor Guide Temporarily Position floor guide just below the center of upper track. stays under the door when it is opened or closed. Leading edge Trailing edge Fasten temporarily through the elongated hole and adjust the guide through the rest of the four holes. Fully closed Fully opened 3 Door (trailing edge) Hanging Door Put a mm support under the door. guide into the groove under the door. Insert the recessed roller into the casing until a click sound is heard. OK CLICK Support Casing Lever is on the bottom Floor guide Lever Roller main body Verify that the roller is not dislocated from the casing, for both door sides. 5
Remove the mm support from under the door. the leading edge (or 50 mm at the trailing edge) before Please refer to the Troubleshooting section. when the soft closer does not work correctly. Trigger cause damage to the soft close mechanism. The of the door should be done with the jump prevention nut loosened. Do not turn adjustment screw beyond adjustment range. Do not use electric screwdriver. Vertical adjustment range: 7 mm 4 mm 3 mm 4 mm Vertical adjustment screw Front-rear adjustment screw Floor guide 613 Clockwise: raise Counterclockwise: lower mm mm 6
Fastening the Jump Prevention Nut The jump prevention nut is on the hanger bolt of the recessed roller. Tighten the nut with the provided spanner until it contacts the soft closer. Jump prevention nut Tighten Be sure to tighten the nut to prevent damaging parts Fasten door stoppers at the s where the door stops. Door stopper (floor) Door close Door open Pan head tapping screw4 30 Door stopper unit Door stopper (floor) Door stopper (floor) 7
Supplement How to remove door Use a mm support under the door. Then pull out the upper roller main unit from the door while raising the lever. It will be easier if you slide the hanger bolt with a spanner. Pay attention not to let the door fall. Spanner Lever Verify that all screws are securely tightened, and verify that all screws have been used. PERIODICAL INSPECTION TROUBLESHOOTING Clean inside of track. Check upper and lower gaps between the door and frame. If necessary, adjust the gaps. Trouble Checkpoint Solution Door stops during soft closing. Then, adjust the door height such that the clearance between the door bottom Using a level gauge, reset upper track horizontally. Reduce the friction between mohair and door. Check if upper track is set horizontally. Check if mohair seal is installed. No soft closing Check if trigger is installed. Install trigger to correct. Abnormal noise during operation The of the trigger catcher may become dislocated. (See section 4.) Check if door touches adjacent parts. Check track rollers for aluminum dust. Check for loose screws retaining the upper track. Then, adjust the door height such that the clearance between the door bottom Provide necessary space between door and adjacent objects. Remove the track and pull out the roller. Then, clean the roller. Tighten the screw. Heavy door operation Check if door touches adjacent parts. Correct door to avoid contact with other objects. Then, adjust the door height such that the clearance between the door bottom Door starts to move. Check if the upper track is set horizontally. Using a level gauge, reset upper track horizontally. SUGATSUNE KOGYO CO.,LTD Tokyo, JAPAN Phone: +81 (0)3 3866 60E-mail:export@sugatsune.co.jp SUGATSUNE KOGYO (UK) LTD Reading, UK Phone: +44 118 97 955 E-mail:sales@sugatsune.co.uk SUGATSUNE EUROPE GmbH Dusseldorf, GERMANY Phone: +49 11 5381900 E-mail:sales@sugatsune.eu 8 SUGATSUNE SHANGHAI Co., LTD Shanghai, CHINA Phone: +86 1 363 1858 E-mail:lamp@sugatsune.com.cn Guangzhou, CHINA Phone: +86 0 6639 355 E-mail:lamp@sugatsune.com.cn SUGATSUNE AMERICA, INC California, USA Phone: +1 3 39 6373E-mail:sales@sugatsune.com Chicago, USA Phone: +1 31 461 81 E-mail:chicagoshowroom@sugatsune.com. SUGATSUNE KOGYO INDIA PRIVATE LIMITED SUGATSUNE CANADA, INC. Mumbai, INDIA Phone: +1 514 31 567 E-mail:support@sugatsune.ca Phone: +91 8314490/91E-mail:sales@sugatsune.in 019.0191-1