SVENSK STANDARD SS-EN ISO 6506-1 Handläggande organ Fastställd Utgåva Sida SVENSK MATERIAL- & MEKANSTANDARD, SMS 1999-09-24 1 1 (1+21+21) Copyright SIS. Reproduction in any form without permission is prohibited. Metallic materials Brinell hardness test Part 1: Test method (ISO 6506-1:1999) Metalliska material Hårdhetsprovning enligt Brinell Del 1: Provningsmetod (ISO 6506-1:1999) The European Standard has the status of a Swedish Standard. This document contains the official English version of with a Swedish translation. This standard supersedes the Swedish Standard SS-EN 10003-1, ed. 1. Swedish Standards corresponding to documents referred to in this Standard are listed in Catalogue of Swedish Standards, issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Europastandarden gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN ISO 6506-1: 1999 med svensk översättning. Standarden ersätter SS-EN 10003-1, utg. 1. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder. ICS 77.040.10 Standarder kan beställas hos SIS som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08-610 30 00. Telefax: 08-30 77 57 Upplysningar om sakinnehållet i standarden lämnas av SMS. Telefon: 08-459 56 00. Telefax: 08-667 85 42 E-post: info@sms-standard.se Prisgrupp R Tryckt i december 1999
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO 6506-1 September 1999 ICS 77.040.10 English version Metallic materials Brinell hardness test Part 1: Test method (ISO 6506-1:1999) Matériaux métalliques Essai de dureté Brinell Partie 1: Méthode d essai (ISO 6506-1:1999) Metallische Werkstoffe Härteprüfung nach Brinell Teil 1: Prüfverfahren (ISO 6506-1:1999) This European Standard was approved by CEN on 8 July 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. E
EUROPASTANDARD EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO 6506-1 September 1999 ICS 77.040.10 Svensk version Metalliska material Brinellprovning Del 1: Provningsmetod (ISO 6505-1:1999) Matériaux métalliques Essai de dureté Brinell Partie 1: Méthode d essai (ISO 6506-1:1999) Metallic materials Brinell hardness test Part 1: Test method (ISO 6506-1:1999) Metallische Werkstoffe Härteprüfung nach Brinell Teil 1: Prüfverfahren (ISO 6506-1:1999) Denna standard är den officiella svenska versionen av. För översättningen svarar SIS. Denna europastandard antogs av CEN 8 juli 1999. CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall ges status som nationell standard. Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centralsekretariat eller från någon av CENs medlemmar. Denna europastandard finns i tre officiella versioner (engelsk, fransk och tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat, har samma status som de officiella versionerna. CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. Nr. Sv
Page 2 Contents Page Foreword... 3 Introduction... 4 1 Scope... 5 2 Normative references... 5 3 Principles... 5 4 Symbols of designations... 5 5 Testing machine... 7 6 Test piece... 7 7 Procedure... 7 8 Uncertainty of the results... 9 9 Test report... 10 Annex A (informative) Procedure for periodic checks of the testing machines by the user... 11 Annex B (normative) Minimum thickness of test piece in relation to the mean diameter of indentation... 12 Annex C (normative) Determination of the Brinell hardness for testing on flat surfaces... 13 Bibliography... 20 Annex ZA (normative) Normative references to the international publications with their relevant European publications... 21
Sida 2 Innehåll Sida Förord.... 3 Inledning... 4 1 Omfattning... 5 2 Normativa hänvisningar... 5 3 Principer... 5 4 Beteckningar och benämningar... 5 5 Provningsutrustning... 7 6 Provstycke... 7 7 Förfarande... 7 8 Osäkerhet i resultaten... 9 9 Provningsrapport... 10 Bilaga A (informativ) Förfarande vid användarens periodiska kontroll av provningsutrustningen... 11 Bilaga B (normativ) Provstyckets minsta tjocklek i förhållande till intryckets medeldiameter... 12 Bilaga C (normativ) Bestämning av Brinellhårdhet vid provning på plana ytor... 13 Litteratur... 20 Bilaga ZA (normativ) Bindande referenser till internationella publikationer med deras motsvarande europeiska publikationer... 21
Page 3 Foreword The text of the International Standard ISO 6506-1:1999 has been prepared by Technical Committee ISO/TC 164 Mechanical testing of metals in collaboration with Technical Committee ECISS/TC 1 Steel testing, the secretariat of which is held by AFNOR. This European Standard supersedes EN 10003-1:1994. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2000, and conflicting national standards shall be withdrawn at the latest by March 2000. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 6506-1:1999 was approved by CEN as a European Standard without any modification. NOTE: Normative references to International Standards are listed in annex ZA (normative).
Sida 3 Förord Texten i den internationella standarden ISO 6506-1:1999 har utarbetats av ISO/TC 164 Mechanical testing of metals i samarbete med ECISS/TC 1 Steel testing. Sekretariatet hålls av AFNOR. Denna europastandard ersätter EN 10003-1:1994. Denna europastandard skall ges status som nationell standard, antingen genom att publicera en identisk text eller genom ikraftsättning senast mars 2000, och motstridande nationella standarder skall dras in senast mars 2000. Enligt CEN/CENELECs interna bestämmelser anmodas följande länder att anta denna europastandard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike. Ikraftsättningsnotering Texten i den internationella standarden ISO 6506-1:1999 är godkänd av CEN som europastandard utan någon ändring. ANM Bindande referenser till internationella publikationer finns i bilaga ZA (del av standarden).
Page 4 Introduction The force values in this part of ISO 6506 were calculated from kilogram force values. They were introduced before the SI-system was adopted. It was decided to keep the values based on the old units for this part of ISO 6506 but for the next revision it will be necessary to consider the advantage of introducing rounded values of test force and possible consequences on the hardness scales. Attention is drawn to the fact that in this part of ISO 6506, only the use of the hardmetal ball indenter is specified. The designation of the Brinell hardness is HBW and should not be confused with the former designation HB, or HBS when a steel ball indenter was used.
Sida 4 Inledning I denna del av ISO 6506 har provkrafter angetts i N och de har beräknats direkt från kilogramkrafter. De infördes innan SI-systemet antogs. Det beslöts att för denna del av ISO 6506 behålla de gamla värdena med vid nästa revidering blir det nödvändigt att beakta fördelen av avrundade värden på provkraften med möjliga konsekvenser för hårdhetsskalorna. Observera det faktum att i denna del av ISO 6506 föreskrivs endast intryckskropp av hårdmetall. Beteckningen för hårdhet enligt Brinell är HBW och får inte förväxlas med den gamla beteckningen för HB eller HBS med intryckskropp av stål.
Page 5 Metallic materials Brinell hardness test Part 1: Test method 1 Scope This part of ISO 6506 specifies the method for the Brinell hardness test for metallic materials and is applicable up to the limit of 650 HBW. For specific materials and/or products, particular International Standards exist (i.e. ISO 4498-1). 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 6506. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 6506 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 4498-1, Sintered metal materials, excluding hardmetals Determination of apparent hardness Part 1: Materials of essentially uniform section hardness. ISO 6506-2:1999, Metallic materials Brinell hardness test Part 2: Verification and calibration of testing machines. 3 Principles An indenter (hardmetal ball with diameter D) is forced into the surface of a test piece and the diameter of the indentation d left in the surface after removal of the force F is measured. The Brinell hardness is proportional to the quotient obtained by dividing the test force by the curved surface area of the indentation. The indentation is assumed to be spherical with a radius corresponding to half of the diameter of the ball. 4 Symbols and designations See Figure 1 and Table 1.
Sida 5 Metalliska material Hårdhetsprovning enligt Brinell Del 1: Provningsmetod (ISO 6506-1:1999) 1 Omfattning Denna del av ISO 6506 beskriver hårdhetsprovning enligt Brinell för metalliska material och är tillämplig upp till HBW 650. För specifika material och/eller produkter finns särskilda internationella standarder (t.ex. ISO 4498-1). 2 Normativa hänvisningar Följande bindande dokument innehåller föreskrifter som genom referens i denna text utgör föreskrifter i denna del av ISO 6506. För daterade referenser är senare ändringar eller revision av någon av dessa publikationer ej tillämpliga. De som träffat överenskommelser baserade på denna del av ISO 6506 uppmuntras emellertid att undersöka möjligheten av att tillämpa senaste utgåvan av nedan angivna bindande dokument. För odaterade referenser gäller senaste utgåva av motsvarande dokument. Medlemmar av ISO och IEC registrerar fortlöpande gällande internationella standarder. ISO 4498-1, Sintered metal materials, excluding hardmetals Determination of apparent hardness Part 1: Materials of essentially uniform section hardness. ISO 6506-2:1999, Metalliska material Hårdhetsprovning enligt Brinell Del 2: Kontroll och kalibrering av provningsmaskiner. 3 Principer En intryckskropp (en kula av hårdmetall med diametern D) pressas mot ytan av en provkropp. Efter avlastning bestäms intryckets diameter d. Brinellhårdheten är proportionell mot kvoten av provkraften och intryckets area. Intrycket antas vara en sfärisk kalott med en radie motsvarande kulans halva diameter. 4 Beteckningar och benämningar Se figur 1 och tabell 1.