SVENSK STANDARD SS-EN ISO 6508-2 Handläggande organ Fastställd Utgåva Sida SVENSK MATERIAL- & MEKANSTANDARD, SMS 1999-09-24 1 1 (1+15+15) Copyright SIS. Reproduction in any form without permission is prohibited. Metallic materials Rockwell hardness test Part 2: Verification and calibration of testing machines (scales A, B, C, D, E, F, G, H, K, N, T) Metalliska material Hårdhetsprovning enligt Rockwell Del 2: Kontroll och kalibrering av provningsutrustning (skalorna A, B, C, D, E, F, G, H, K, N, T) The European Standard has the status of a Swedish Standard. This document contains the official English version of EN ISO 6508-2: 1999 with a Swedish translation. This standard supersedes the Swedish Standard SS-EN 10109-2, edition 1. Swedish Standards corresponding to documents referred to in this Standard are listed in Catalogue of Swedish Standards, issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Europastandarden gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av EN ISO 6508-2: 1999 med svensk översättning. Standarden ersätter SS-EN 10109-2, utgåva 1. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder. ICS 77.040.10 Standarder kan beställas hos SIS som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08-610 30 00. Telefax: 08-30 77 57 Upplysningar om sakinnehållet i standarden lämnas av SMS. Telefon: 08-459 56 00. Telefax: 08-667 85 42 E-post: info@sms-standard.se Prisgrupp R Tryckt i december 1999
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO 6508-2 September 1999 ICS 77.040.10 English version Metallic materials Rockwell hardness test Part 2: Verification and calibration of testing machines (scales A, B, C, D, E, F, G, H, K, N, T) Matériaux métalliques Essai de dureté Rockwell Partie 2: Vérification et étalonnage des machines d essai (échelles A, B, C, D, E, F, G, H, K, N, T) Metallische Werkstoffe Härteprüfung nach Rockwell (Skalen A, B, C, D, E, F, G, H, K, N, T) Teil 2: Prüfung und Härteprüfmaschinen This European Standard was approved by CEN on 8 July 1999. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. E
EUROPASTANDARD EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN ISO 6508-2 September 1999 ICS 77.040.10 Svensk version Metalliska material Hårdhetsprovning enligt Rockwell Del 2: Kontroll och kalibrering av provningsutrustning (skalorna A, B, C, D, E, F, G, H, K, N, T) Matériaux métalliques Essai de dureté Rockwell Partie 2: Vérification et étalonnage des machines d essai (échelles A, B, C, D, E, F, G, H, K, N, T) Metallic materials Rockwell hardness test Part 2: Verification and calibration of testing machines (scales A, B, C, D, E, F, G, H, K, N, T) Metallische Werkstoffe Härteprüfung nach Rockwell (Skalen A, B, C, D, E, F, G, H, K, N, T) Teil 2: Prüfung und Härteprüfmaschinen Denna standard är den officiella svenska versionen av. För översättningen svarar SIS. Denna europastandard antogs av CEN den 8 juli 1999. CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall ges status som nationell standard. Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centralsekretariat eller från någon av CENs medlemmar. Denna europastandard finns i tre officiella versioner (engelsk, fransk och tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat, har samma status som de officiella versionerna. CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. Nr. Sv
Page 2 Contents Page Foreword... 3 Introduction... 4 1 Scope... 5 2 Normative reference... 5 3 General conditions... 6 4 Direct verification... 6 5 Indirect verification... 9 6 Intervals between verifications... 12 7 Verification report/calibration certificate... 12 Annex A (normative) Repeatability of testing machines... 13 Annex ZA (normative) Normative references to international publications with their relevant European publications... 15
Sida 2 Innehåll Sida Förord... 3 Inledning... 4 1 Omfattning... 5 2 Normativa hänvisningar... 5 3 Allmänna betingelser... 6 4 Direkt kontroll... 6 5 Indirekt kontroll... 9 6 Intervall mellan kontroller... 12 7 Kontrollrapport/kalibreringsintyg... 12 Bilaga A (normativ) Repeterbarhet för provningsmaskiner... 13 Bilaga ZA (normativ) Bindande referenser till internationella publikationer med deras motsvarande europeiska publikationer... 15
Page 3 Foreword The text of the International Standard ISO 6508-2:1999 has been prepared by Technical Committee ISO/TC 164 Mechanical testing of metals in collaboration with Technical Committee ECISS/TC 1 Steel testing, the secretariat of which is held by AFNOR. This European Standard supersedes EN 10109-2:1994. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2000, and conflicting national standards shall be withdrawn at the latest by March 2000. According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 6508-2:1999 was approved by CEN as a European Standard without any modification. NOTE: Normative references to International Standards are listed in annex ZA (normative).
Sida 3 Förord Texten i den internationella standarden ISO 6508-2:1999 har utarbetats av ISO/TC 164 Mechanical testing of metals i samarbete med ECISS/TC 1 Steel testing. Sekretariatet hålls av AFNOR. Denna europastandard ersätter EN 10109-2:1994. Denna europastandard skall ges status som nationell standard, antingen genom att publicera en identisk text eller genom ikraftsättning senast mars 2000, och motstridande nationella standarder skall dras in senast mars 2000. Enligt CEN/CENELECs interna bestämmelser anmodas följande länder att anta denna europastandard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tyskland och Österrike. Ikraftsättningsnotering Texten i den internationella standarden ISO 6508-2:1999 är godkänd av CEN som europastandard utan någon ändring. ANM Bindande referenser till internationella publikationer finns i bilaga ZA (normativ).
Page 4 Introduction The force values in this part of ISO 6508 were calculated from kilogram force values. They were introduced before the SI-system was adopted. It was decided to keep the values based on the old units for this part of ISO 6508 but for the next revision it will be necessary to consider the advantage of introducing rounded values of test force and the consequence on the hardness scales. Attention is drawn to the fact that in this part of ISO 6508, the use of hardmetal balls as indenters is equivalent to the use of steel balls; however, it is indicated that the measurements made with the two ball types give different results.
Sida 4 Inledning I denna del av ISO 6508 har provkrafter angetts i N och de har beräknats direkt från kilogramkrafter. De infördes innan SI-systemet antogs. Det beslöts att för denna del av ISO 6508 behålla de på de gamla enheterna grundade värdena men vid nästa revision blir det nödvändigt att beakta fördelen av avrundade värden på provkraften och konsekvensen för hårdhetsskalorna. Observera att i denna del av ISO 6508 behandlas användningen av hårdmetallkulor som likvärdig med användningen av stålkulor. Det anges emellertid att mätningar med de två kultyperna ger olika resultat.
Page 5 Metallic materials Rockwell hardness test Part 2: Verification and calibration of testing machines (scales A, B, C, D, E, F, G, H, K, N, T) 1 Scope This part of ISO 6508 specifies a method of verification of testing machines for determining Rockwell hardness (scales A, B, C, D, E, F, G, H, K, N, T). It specifies a direct method for checking the main functions of the machine and an indirect method suitable for the overall checking of the machine. The indirect method may be used on its own for periodic routine checking of the machine in service. If a testing machine is also to be used for other methods of hardness testing, it shall be verified independently for each method. This part of ISO 6508 is applicable to portable hardness testing machines with the exception of requirements in 6.1 a) in which the word relocation does not apply. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 6508. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 6508 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 376, Metallic materials Calibration of force-proving instruments used for verification of uniaxial testing machines. ISO 3878, Hardmetals Vickers hardness test. ISO 6507-1:1997, Metallic materials Vickers hardness test Part 1: Test method. ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T). ISO 6508-3, Metallic materials Rockwell hardness test Part 3: Calibration of reference blocks (scales A, B, C, D, E, F, G, H, K, N, T).
Sida 5 Metalliska material Hårdhetsprovning enligt Rockwell Del 2: Kontroll och kalibrering av provningsmaskiner (skalorna A, B, C, D, E, F, G, H, K, N, T) 1 Omfattning Denna del av ISO 6508 beskriver en metod för kontroll av provningsmaskiner för bestämning av Rockwellhårdhet (skalorna A, B, C, D, E, F, G, H, K, N, T). Den beskriver en direkt metod för kontroll av maskinens huvudfunktioner och en indirekt metod för fullständig kontroll av maskinen. Den indirekta metoden kan användas för sig för periodisk rutinkontroll av maskinen i drift. Om en provningsmaskin används också för andra metoder för hårdhetsprovning, skall den verifieras för varje metod för sig. Denna del av ISO 6508 kan användas för bärbara maskiner för hårdhetsprovning, med undantag för fordringar i avsnitt 6.1a) där ordet förflyttning ej är tillämpligt. 2 Normativa hänvisningar Följande bindande dokument innehåller föreskrifter som genom referens i denna text utgör föreskrifter i denna del av ISO 6506. För daterade referenser är senare ändringar eller revision av någon av dessa publikationer ej tillämpliga. De som träffat överenskommelser baserade på denna del av ISO 6506 uppmuntras emellertid att undersöka möjligheten av att tillämpa senaste utgåvan av nedan angivna bindande dokument. För odaterade referenser gäller senaste utgåva av motsvarande dokument. Medlemmar av ISO och IEC registrerar fortlöpande gällande internationella standarder. ISO 376, Metallic materials Calibration of force proving instruments used for verification of uniaxial testing machines ISO 3878, Hardmetals Vickers hardness test ISO 6507-1:1997, Metalliska material Hårdhetsprovning enligt Vickers Del 1: Provningsmetod ISO 6508-1:1999, Metalliska material Hårdhetsprovning enligt Rockwell Del 1: Provningsmetod (skalorna A, B, C, D, E, F, G, H, K, N, T) ISO 6508-3:1999, Metalliska material Hårdhetsprovning enligt Rockwell Del 3: Kalibrering av referensblock (skalorna A, B, C, D, E, F, G, H, K, N, T)