SVENSK STANDARD SS-EN 10084 Handläggande organ Fastställd Utgåva Sida SVENSK MATERIAL- & MEKANSTANDARD, SMS 1998-08-28 1 1 (1+48) INNEHÅLLET I SVENSK STANDARD ÄR UPPHOVSRÄTTSLIGT SKYDDAT. SIS HAR COPYRIGHT PÅ SVENSK STANDARD. EFTERTRYCK UTAN TILLSTÅND ÄR FÖRBJUDET. Case hardening steels Technical delivery conditions Sätthärdningsstål Tekniska leveransbestämmelser The European Standard has the status of a Swedish Standard. This document contains the official English version of with a Swedish translation. This standard replaces Swedish standards for case hardening steels according to the table below. Swedish Standards corresponding to documents referred to in this Standard are listed in Catalogue of Swedish Standards, issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Europastandarden gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av med svensk översättning. Standarden ersätter tidigare svensk standard för sätthärdningsstål enligt nedanstående tabell. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder. Denna standard Materialbeteckning 1) This standard Material designation 1) Namn Name Nummer Number C15R 1.1140 13 70 16MnCrS5 1.7139 21 27 20NiCrMoS2-2 1.6526 25 06 16NiCrS4 1.5715 25 11 25 12 17NiCrMoS6-4 1.6569 25 23 1) 1) Tidigare svensk standard, SS-stål Former Swedish standard, SS steel Beteckning Designation Närmast motsvarande europastandard, ISO-standard och tidigare nationell standard framgår även av SMS Materialnyckel. The nearest corresponding European, ISO and former national standard may also be found in SMS Materialnyckel, Handbok 19. ICS 77.140.10 Standarder kan beställas hos SIS som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08-610 30 00. Telefax: 08-30 77 57 Upplysningar om sakinnehållet i standarden lämnas av SMS. Telefon: 08-459 56 00. Telefax: 08-667 85 42 E-post: info@sms-standard.se Prisgrupp S Tryckt i december 1998
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 10084 April 1998 ICS 77.140.10 Descriptors: iron and steel products, hot-rolled products, structural steels, case hardening, designation, steel grades, chemical composition, characteristics, dimensions, surface condition, heat treatment, hardenability, hardness, inspection, delivery English version Case hardening steels Technical delivery conditions Aciers pour cémentation Condition techniques de livraison Einsatzstähle Technische Lieferbedingungen This European Standard was approved by CEN on 27 March 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. E
EUROPASTANDARD EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM Provläsningsexemplar / Preview EN 10084 April 1998 ICS 77.140.10 Nyckelord: järn- och stålprodukter, varmvalsade produkter, konstruktionsstål, sätthärdning, beteckning, stålsorter, kemisk sammansättning, egenskaper, mått, ytbeskaffenhet, värmebehandling, härdbarhet, hårdhet, kontroll, leverans Svensk version Sätthärdningsstål Tekniska leveransbestämmelser Aciers pour cémentation Condition techniques de livraison Case hardening steels Technical delivery conditions Einsatzstähle Technische Lieferbedingungen Denna standard är den officiella svenska versionen av. För översättningen svarar SIS. Denna europastandard antogs av CEN 27 mars 1998. CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall ges status som nationell standard. Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centralsekretariat eller från någon av CENs medlemmar. Denna europastandard finns i tre officiella versioner (engelsk, fransk och tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat, har samma status som de officiella versionerna. CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. Nr. Sv
Page 2 Provläsningsexemplar / Preview Contents Page Foreword... 3 1 Scope... 4 2 Normative references... 4 3 Definitions... 5 4 Classification and designation... 6 4.1 Classification... 6 4.2 Designation... 6 5 Information to be supplied by the purchaser... 6 5.1 Mandatory information... 6 5.2 Options... 6 6 Manufacturing process... 7 6.1 Melting process... 7 6.2 Deoxidation... 7 6.3 Manufacture of the product... 7 6.4 Heat treatment condition and surface finish at the time of delivery... 7 6.5 Cast separation... 7 7 Requirements... 7 7.1 Chemical composition, hardness and hardenability... 7 7.2 Technological properties... 7 7.3 Structure... 8 7.4 Internal soundness... 8 7.5 Surface quality... 8 7.6 Dimensions, tolerances on dimensions and shape... 9 8 Inspection and testing... 9 8.1 Types and contents of inspection documents... 9 8.2 Specific inspection and testing... 9 9 Marking... 10 Annex A (normative): Supplementary or special requirements... 30 Annex B (informative): Bibliography... 31 Annex C (informative): Dimensional standards applicable to products complying with this European Standard... 32 Annex D (normative): Determining the non-metallicinclusion content... 33 Annex E (informative): Comparison of steel gradesspecified in this European Standard andiso 683-11:1987 and other steel grades previously standardized nationally... 34 Annex F (informative): Classification of steel grades according to minimum tensile strength as a function of diameter after quenching and tempering at 200 C... 35
Sida 2 Innehåll Sida Förord... 3 1 Omfattning... 4 2 Hänvisning till standard... 4 3 Definitioner... 5 3.1 Sätthärdningsstål...5 4 Klassificering och beteckning... 6 4.1 Klassificering... 6 4.2 Beteckning... 6 5 Information som skall lämnas av köparen... 6 5.1 Obligatorisk information... 6 5.2 Valfri information... 6 6 Tillverkningsmetod... 7 6.1 Metod för smältning... 7 6.2 Desoxidation... 7 6.3 Tillverkning av formvaror... 7 6.4 Värmebehandling och ytbeskaffenhet vid leverans... 7 6.5 Separering av charger... 7 7 Fordringar... 7 7.1 Kemisk sammansättning, hårdhet och härdbarhet... 7 7.2 Teknologiska egenskaper... 8 7.3 Struktur... 8 7.4 Frihet från inre fel... 8 7.5 Ytbeskaffenhet... 8 7.6 Dimensioner och toleranser på mått och form... 9 8 Kontroll och provning... 9 8.1 Typer av och innehåll i kontrollintyg... 9 8.2 Specifik kontroll och provning... 9 9 Märkning... 10 Bilaga A (del av standard): Tilläggs- eller specialfordringar... 30 Bilaga B (ej del av standard): Litteraturförteckning... 31 Bilaga C (ej del av standard): Dimensionsstandarder tillämpliga på formvaror enligt denna europastandard... 32 Bilaga D (del av standard): Bestämning av halt av ickemetalliska inneslutningar... 33 Bilaga E (ej del av standard): Jämförelse mellan stål angivna i denna europastandard och i ISO 683-11:11997 och andra stål som tidigare standardiserats nationellt... 34 Bilaga F (ej del av standard): Klassificering av stål efter minsta brottgräns som funktion av diameter efter härdning och anlöpning vid 200 C... 35
Page 3 Provläsningsexemplar / Preview Foreword This European Standard has been prepared by Technical Committee ECISS/TC 23. Steels for heat treatment, alloy steels and free-cutting steels Qualities, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 1998, and conflicting national standards shall be withdrawn at the latest by October 1998. In accordance with the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
Sida 3 Förord Denna europastandard har utarbetats av ECISS/TC 23, Stål för värmebehandling, legerade stål och automatstål Stålsorter. Sekretariatet hålls av DIN. Denna europastandard skall ges status som nationell standard, antingen genom att publicera en identisk text eller genom ikraftsättning senast oktober 1998, och motstridande nationella standarder skall dras in oktober 1998. Enligt CEN/CENELECs interna bestämmelser är följande länder bundna att anta denna europastandard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.
Page 4 Provläsningsexemplar / Preview 1 Scope 1.1 This European Standard gives the technical delivery requirements for semi-finished products, hot formed, for example blooms, billets, slabs (see notes 2 and 3) bars (see note 2) rod wide flats hot-rolled sheet/plate and strip hammer and drop forgings (see note 2) manufactured from the case hardening unalloyed or alloyed steels (see note 4) listed in table 3 and supplied in one of the heat treatment conditions given for the different types of products in table 1, lines 2 to 7 and in one of the surface conditions given in table 2. The steels are in general intended for the fabrication of case-hardened (see clause 3.) machine parts. NOTE 1: EURONORMS or European Standards relating to steels complying with the requirements for the chemical composition in table 3 but which are supplied in other product forms or treatment conditions than given above or are intended for special applications, and EURONORMS or European Standards for similar steel grades are listed in annex B. NOTE 2: Hammer-forged semi-finished products (blooms, billets, slabs, etc.) and hammerforged bars are included under semi-finished products or bars and not under the term "hammer and drop forgings". NOTE 3: Special agreements shall be made when ordering undeformed continuously cast semi-finished products. NOTE 4: In accordance with EN 10020, the steels covered by this European Standard are special steels. 1.2 In special cases variations in these technical delivery requirements or additions to them may form the subject of an agreement at the time of enquiry and order (see annex A). 1.3 In addition to the specifications of this European Standard, the general technical delivery requirements of EN 10021 are applicable, unless otherwise specified. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 10003-1 EN 10020 EN 10021 EN 10027-1 EN 10027-2 EN 10052 Metallic materials Brinell hardness test Part 1: Test method Defintion and classification of grades of steel General technical delivery requirements for steel and iron products Designation systems for steel Part 1: Steel names, principal symbols Designation systems for steel Part 2: Numerical system Vocabulary of heat treatment terms for ferrous products
Sida 4 1 Omfattning 1.1 Denna europastandard anger tekniska leveransbestämmelser för varmbearbetade halvfabrikat, t.ex. blooms, billets, slabs (ämnen) (se not 2 och 3) stång (se not 2) valstråd bredplattstång varmvalsad plåt och band hammar- och sänksmide (se not 2) tillverkade av de i tabell 3 upptagna olegerade och legerade sätthärdningsstålen (se not 4) och levererade i något av de värmebehandlingstillstånd som för de olika typerna av formvaror anges i tabell 1, rad 2-7 och med ytutföranden enligt något av alternativen i tabell 2. Stålen är i allmänhet avsedda för tillverkning av sätthärdade (se avsnitt 3) maskindelar. ANM 1: EURONORMER eller europastandarder för stål som uppfyller fordringarna för kemisk sammansättning enligt tabell 3 men som levereras i andra formvaror eller med annan behandling än som angetts ovan eller är avsedda för särskilda tillämpningar, och EURONORMER eller europastandarder för liknande stål är upptagna i bilaga B. ANM 2: Hammarsmidda halvfabrikat (ämnen) och hammarsmidd stång inkluderas i halvfabrikat eller stång och ej under beteckningen hammar- och sänksmiden. ANM 3: Särskild överenskommelse.skall träffas vid beställning av obearbetade kontinuerligt gjutna halvfabrikat. ANM 4: Enligt EN 10020 är stål enligt denna europastandard specialstål. 1.2 I särskilda fall kan avvikelser från dessa tekniska leveransbestämmelser eller tillägg till dem bli föremål för överenskommelse vid förfrågan och beställningstillfället (se bilaga A). 1.3 Utöver bestämmelserna i denna europastandard är de allmänna tekniska leveransbestämmelserna enligt EN 10021 tillämpliga, såvida ej annat föreskrivs. 2 Hänvisning till standard Denna standard innehåller daterade eller odaterade hänvisningar till regler i andra publikationer. Dessa normativa hänvisningar återfinns i den löpande texten. Publikationerna anges nedan. Beträffande daterade hänvisningar till publikationer som senare har ändrats eller fått tillägg, gäller dessa ändringar eller tillägg endast då de har införts i denna standard. Vid odaterade hänvisningar gäller den senaste utgåvan av publikationen. EN 10003-1 Metalliska material Hårdhetsprovning enligt Brinell Del 1: Provningsmetod EN 10020 EN 10021 EN 10027-1 EN 10027-2 EN 10052 Definition och klassificering av ståltyper Allmänna tekniska leveransbestämmelser för järn- och stålprodukter Stålbeteckningar Del 1: Alfanumeriskt system Stålbeteckningar Del 2: Numeriskt system Termer för värmebehandling av järn- och stålprodukter.
Page 5 Provläsningsexemplar / Preview EN 10079 EN 10109-1 EN 10163-2 Definition of steel products Metallic materials Hardness test Part 1: Rockwell test (scales A, B, C, D, E, F, G, H, K) and Rockwell superficial test (scales 15N, 30N, 45N, 15T, 30T and 45T) Delivery requirements for surface condition of hot rolled steel plates, wide flats and sections Part 2: Plates and wide flats EN 10204 Metallic products Types of inspection documents (includes amendment A1:1995) EN 10221 Surface quality classes for hot-rolled bars and rods Technical delivery conditions CR 10260 ECISS IC 10 Designation systems for steel Additional symbols for steel names EN ISO 377 EURONORM 23 1) EURONORM 103 1) ISO 14284 DIN 50602:1985 NF A 04-106:1984 SS 11 11 16:1987 Steel and steel products Location and preparation of test pieces for mechanical testing End quench hardenability test for steel (Jominy test) Microscopic determination of the ferritic or austenitic grain size of steels Steel and iron Sampling and preparation of samples for the determination of chemical composition Metallographic examination Microscopic examination of special steels using standard diagrams to assess the content of non-metallic inclusions Iron and steel Methods of determination of non metallic inclusions in wrought steel Part II: Micrographic method using standard diagrams Steel Methods for assessment of the content of nonmetallic inclusions Microscopic methods Jernkontoret s inclusion chart II for the assessment of non-metallic inclusions. 3 Definitions For the purpose of this European Standard the following definition applies in addition to the definitions in EN 10020, EN 10021, EN 10052, EN 10079, EN ISO 377 and ISO 14284: 3.1 Case-hardening steels Steels with a relatively low carbon content which are intended for carburising or carbonitriding and subsequent hardening. Such steels, after treatment, are characterised by a high hardness surface layer and a tough core. 1) If may be agreed at the time of ordering, until this EURONORM has been adopted as a European Standard, thar either this EURONORM or a corresponding national standard should be applied.
Sida 5 EN 10079 EN 10109-1 EN 10163-2 EN 10204 EN 10221 CR 10260 EN ISO 377 EURONORM 23 1) EURONORM 103 1) ISO 14284 DIN 50602:1985 NF A 04-106:1984 SS 11 11 16:1987 Definition av formvaror för stål Metalliska material Hårdhetsprovning Del 1: Rockwellprovning (skalorna A, B, C, D, E, F, G, H, K) och Rockwellsuperficialprovning (skalorna 15N, 30N, 45N, 15T, 30T och 45T) Leveransbestämmelser för ytbeskaffenhet hos varmvalsad plåt, bred plattstång och profiler av stål Del 2: Plåt och bredplattstång Metalliska varor Typer av kontrollintyg (inklusive ändring A1:1995) Ytklasser för varmvalsad stång och valstråd Tekniska leveransbestämmelser ECISS IC 10 Designation systems for steel Additional symbols for steel names Steel and steel products Location and preparation of test pieces for mechanical testing End quench hardenability test for steel (Jominy test) Microscopic determination of the ferritic or austenitic grain size of steels Steel and iron Sampling and preparation of samples for the determination of chemical composition Metallographic examination Microscopic examination of special steels using standard diagrams to assess the content of non-metallic inclusions Iron and steel Methods of determination of non metallic inclusions in wrought steel Part II: Micrographic method using standard diagrams Stål Bedömning av icke-metalliska inneslutningar Mikrometoder Jernkontorets skala II för kvantitativ bedömning 3 Definitioner För denna europastandard gäller definitionerna i EN 10020, EN 10021, EN 10079, EN ISO 377 och ISO 14284. 3.1 Sätthärdningsstål Stål med relativt låg kolhalt som är avsedda för uppkolning eller karbonitrering och efterföljande härdning. Efter behandling karakteriseras sådana stål av ett hårt ytskikt och en seg kärna. 1) Till dess att denna EURONORM har överförts till en europastandard skall denna eller motsvarande nationell standard tillämpas beroende på överenskommelse vid beställningstillfället.