Portable fire extinguishers - Part 2: Tightness, dielectric test, tamping test, special provisions Brand och räddning - Handbrandsläckare - Del 2: Bibehållande av tryck, dielektrisk provning, kompakteringsprovning, särskilda bestämmelser The European Standard has the status of a Swedish Standard. This document contains the official English version of with a Swedish translation. This standard supersedes the Swedish Standard SS 1192, edition, January lst, 1997. EN 3 differentiates between s.c. low-temperature and normal countries. As Sweden is a s.c. low-temperature country tests shall be carried out at 30 C where EN 3 states 20 C. EN 3-3:199 Portable fire extinguishers Construction, resistance to pressure, mechanical tests, has not been implemented by Sweden. In Sweden the following regulations apply: Swedish Board of Occupational Safety and Health s ordinances on Pressure Vessels, AFS 198:9 amended in AFS 199:39 and on Gas Cylinders, AFS 1992: amended in APS 199:38. In the foreword of EN 3 a reference is given to part Provisions for the attestation of conformity of portable fire extinguishers in accordance with EN 3 part 1 to. EN 3- is currently being revised with the aim to be published at the end of 199. Swedish Standards corresponding to documents referred to in this Standard are listed in Catalogue of Swedish Standards, annually issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Europastandarden gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av med svensk översättning Standarden ersätter SS 1192, utgår, från och med den 1 januari 1997. I EN 3 skiljs på länder med varma resp. låga temperaturer; eftersom Sverige måste anses vara ett lågtemperaturland skall handbrandsläckare provas vid 30 C där EN 3 anger 20 C som normaltemperatur. EN 3-3:199 Portable fire extinguishers Construction, resistance to pressure, mechanical tests, är ej fastställd av Sverige. I Sverige gäller Arbetarskyddsstyrelsens föreskrifter om Tryckkärl, AFS 198:9, senast ändrad i AFS 199:39 samt föreskrifter om Gasflaskor, AFS 1992:, senast ändrad i AFS 199:38. I förordet till EN 3 anges del Bestämmelser för bestyrkande om släckares överensstämmelse med EN 3 del 1 -. EN 3- revideras f.n. och beräknas bli publicerad i slutet av 199. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som årligen ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder.
EUROPEAN STANDARD EN 3-2 NORME EUROPÉENNE EUROPÄISCHE NORM February 199 ICS 13.220.30 Descriptors: fire fighting, fire equipment, fire extinguishers, movable extinguishers, portable equipment, tests, leak tests, dielectric strength tests, compression tests English version Portable fire extinguishers - Part 2: Tightness, dielectric test, tamping test, special provisions Extincteurs d incendie portatifs Partie 2: Etanchéité, essai diélectrique, essai de tassement, dispositions spéciales Tragbare Feuerlöscher Teil 2: Dichtheidsprüfung, prüfung der elektrischen Leitfähigkeit, Verdichtungsprüfung, Besondere Anforderungen This European Standard was approved by CEN on 199-09-1. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 3, B -100 BRUSSELS 199 Copyright reserved to CEN member Ref. No. E
EUROPASTANDARD EN 3-2 EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM Februari 199 ICS 13.220.30 Nyckelord: brandsläckning, brandutrustning, mobila släckare, bärbara utrustningar, provning, läckageprovning, dielektrisk provning, komprimeringsprovning Svensk version Brand och räddning - Handbrandsläckare - Del 2: Bibehållande av tryck, dielektrisk provning, kompakteringsprovning, särskilda bestämmelser Extincteurs d incendie portatifs - Portable fire extinguishers - Tragbare Feuerlöscher - Teil 2: Partie 2: Etanchéité, essai Part 2: Tightness, dielectric test, Dichtheidsprüfung, prüfung der diélectrique, essai de tassement, tamping test, special provisions elektrischen Leitfähigkeit, dispositions spéciales Verdichtungsprüfung, Besondere Anforderungen Denna standard är den officiella svenska versionen av. För, översättningen svarar SIS. Denna europastandard antogs av CEN 199-09-1. CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall utges som nationell standard. Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENS Centralsekretariat eller från någon av CENS medlemmar. Denna europastandard finns i tre officiella versioner; engelsk, fransk och tysk. En version på ett annat språk, översatt under ansvar av en CEN-medlem till det egna språket och anmäld till CENS Centralsekretariat har samma status som de officiella versionerna. CENS medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tyskland, och Österrike European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 3, B -100 BRUSSELS 199 Copyright reserved to CEN members Ref. No. Sv
Page 2 CONTENTS Page 1 2 3 3.1 3.2.1.2.1.2.3. Foreword Scope Normative reference Tightness Verification Acceptance Levels Dielectric test Purpose of Test Measures of the current Tamping Test Special Provisions Controlled discharge Operation position Hose Assembly Propellants 3 Annex A (normative) : Dielectric test 7 Annex B (normative) : Tamping test 8 Annex C (informative) : National deviation 9
Sida 2 Innehållsförteckning Sida Förord............................................................3 1 Omfattning.................................................... 2 Bindande referenser.......................................... 3 Täthet....................................................... 3.1 Kontroll.................................................... 3.2 Tillåtna nivåer............................................... Dielektriskprovning............................................1 Provningens syfte.............................................2 Mätning av ström............................................... Kompakteringsprovning....................................... Särskilda bestämmelser.........................................1 Reglerad tömning.................................................2 Funktionsdugligt läge............................................3 Slang......................................................... Utdrivningsmedel............................................ Bilaga A (del av standarden): Dielektrisk provning...................... 7 Bilaga B (del av standarden): Kompakteringsprovning.................. 8 Bilaga C (ej standard): Nationella avvikelser....................... 9
Page 3 FOREWORD This European Standard has been prepared by Technical Committee CEN/TC 70 Manuel means of fire fighting equipment, the secretariat of which is held by IBN. This European Standard supersedes EN 3-2:1978. This European Standard is one part of EN 3 prepared by CEN/TC 70. This European Standard EN 3 consist of Parts and has the generic title Portable fire extinguishers and the following different subtitles : - Part 1 : - Part 2 : - Part 3 : - Part : - Part : - Part : Description r duration of operation, class A and B fire test Tightness, dielectric test, tamping test, special provision Construction, resistance to pressure, mechanical tests Charges, minimum required fire Specifications and supplementary tests Provisions for the attestation of conformity of portable fire extinguishers in accordance-with EN 3 Part 1 to Part This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement at the latest August 199, and conflicting national standards shall be withdrawn at the latest by January 1997. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Danmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Sida 3 Förord Denna europeiska standard har utarbetats inom CEN/TC 70 Släckredskap (bärbara/transportabla) med sekretariat från Belgien. Denna europeiska standard ersätter EN 3-2:1978. EN 3 - Handbrandsläckare består av delar enligt följande: Del 1: Beskrivning av tömningstid, provning mot klass A- och B-bål Del 2: Bibehållande av tryck, dielektrisk provning, kompakteringsprovning, särskilda bestämmelser Del 3: Konstruktion, hållfasthet mot tryck, mekaniska provningar Del : Släckförmåga, minimikrav för provbål Del : Kompletterande krav och provningar Del : Bestämmelser för bestyrkande om släckares överensstämmelse med EN 3 del 1 - Denna europeiska standard skall ges ut som nationell standard, antingen genom publicering av identisk text eller genom ikraftsättning senast augusti 199. Motstridig nationell standard skall vara indragen senast januari 1997. Enligt CEN/CENELEC-reglerna är följande länder skyldiga att implementera denna europeiska standard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tyskland och Österrike.
Page 1 Scope This Standard specifies and special provisions the tightness, the dielectric test, the tamping test applicable to portable fire extinguishers. 2 Normative reference This European Standard incorporates by dated or undated references, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment of revision. For undated reference the latest edition of the publication referred to applies. EN 3-1:199* Portable fire extinguishers - Part 1: Designation, duration of operation, class A and B fire test. 3 Tightness All extinguishers and gas cartridges shall be designed in permit their retention of charge to be verified at regular 3.1 Verification 3.1.1 Retention of charge shall be checked by weighing for such a way intervals. : as to - CO 2 cartridges; - CO 2 extinguishers; - Halon extinguishers, these shall also be verified for pressure. The appropriate markings shall be shown on the main body of these appliances. 3.1.2 It shall be possible to check the retention of charge of stored pressure extinguishers by measuring the internal pressure, with the exception of CO 2 extinguishers. These shall be obtained in one of the following ways. a) By means of a connection to enable the internal pressure to be checked directly by an independent apparatus. Such a connection shall be fitted with a Pressure retaining cap and shall communicate directly to the contents under pressure. A removable pressure indicating device may be considered as a pressure retaining cap. b) By means of a built-in pressure indicating device which can itself be checked independently that it is in good working order by the application of an external pressure. (see C.2) *In the original English version the year was incorrectly 199.