Hose reel ORB Slangrulle ORB 24974, 24975, 24976 24977, 44452, 44453 24978, 24979 Manual Alentec & Orion AB, Box 108, 132 23 Saltsjö-Boo Telefon: +46 8 747 67 00 Fax: +46 8-715 20 74 e-mail: info@alentec.se www.alentec.com Manual Hose Reel ORB, Rev 1a, 12-05-29
(EN) Safety Precautions (SE) Säkerhetsanvisning This equipment is for professional use only. Do not leave the hose to coil unattended. Ensure that the pressure does not exceed maximum working pressure of the lowest rated system component. To assure the function of the hose reel, it is important to choose a model that is compatible with the fluid and pressure. Release the pressure inside the reel before servicing. The spring is always under great tension. Always contact your supplier or service centre to change the spring. Fluids under pressure can cause serious injury. Släpp inte taget om slangen vid upprullning, detta kan skada slangrullen, utrustning och personer i dess närhet. Säkerställ att systemets arbetstryck inte överstiger den lägst klassade systemkomponenten. För att säkerställa slangrullens funktion är det mycket viktigt att använda rätt modell för respektive vätska, tryck och temperatur. Släpp på trycket i slangrullen innan service utförs. Slangrullens fjäder är alltid kraftigt spänd. Kontakta alltid er distributör eller service center för byte av fjäder. Vätskor under högt tryck kan orsaka allvarliga skador. (EN) Description Open hose reel for air, water (low pressure), antifreeze, vacuum and lubricants depending on model. Hose can be uncoiled and latched at the desired length. By pulling the hose, the latch is released and the hose is automatically rewound. (SE) Beskrivning Öppen slangrulle för luft, vatten (lågt tryck), kylarvätska, vakuum och olja beroende på modell. Slangen kan dras ut och spärras i önskat läge. Genom att återigen dra i slangen lossas spärren och slangen rullas tillbaka. Fig. 1 2(9)
(EN) Installation The hose reel can be installed directly on the fixing surface in the ceiling, on the wall or on the floor. For optimal operation, the reel outlet guide arms should be mounted in the positions shown in figure 1. For ceiling, wall or column mounted reel, the minimum recommended height is 2.5 m (8 feet). To move the outlet guide arms, follow these steps: 1. Place the reel on a flat surface for easy manipulation of the components. 2. Loosen the screws (1) that hold the arms and rotate them to the desired position (Fig. 2). 3. Fix the arms firmly in the new position of the hose reel body by means of the corresponding screws. To change position of the hose stopper, pull out the hose to the desired length and latch it. Loosen the hose stopper and place it at the desired position and fasten it (see Fig 3). (SE) Installation Slangrullen kan installeras direkt på monteringsytan både i tak, på vägg och på golv. För att uppnå bästa funktion bör slangrullens utloppsarmar monteras i positionerna som visas i figur 1. För montage i tak eller på vägg/ pelare rekommenderas en min höjd på 2.5 m. För att ändra utloppsarmarnas position, följ dessa steg: 1. Placera slangrullen på ett plant underlag för att lätt kunna demontera/ montera delarna. 2. Skruva loss skruvarna (1) som håller slangrullens utloppsarmar och rotera dem till lämplig position. (Fig. 2). 3. Montera armarna i deras nya position och skruva fast dem ordentligt med skruvarna. För att byta position på slangstoppet, drag ut slangen och hitta spärrläge på önskad längd. Lossa slangstoppet, flytta det till önskad position och sätt fast det ordentligt (Fig 3). Fig. 1 Fig. 2 Fig. 3 3(9)
(EN) Hose installation (SE) Montering av slang Clamp the hose reel firmly to a work bench. Introduce the hose end that is to be connected to the hose reel through the outlet guide and then through the opening in the drum of the spool. Pull the hose through the drum towards the swivel. Connect the hose to the swivel as indicated in (2) and fasten the U-clamp with the nuts as shown in (1) (Fig 4). Coil the hose onto the spool by turning the spool. When all the hose is coiled, pretension the hose reel power spring by rotating the spool further: 15m hose : +8 turns, 20m hose: +5 turns 25m hose: +5 turns, 30m hose: +1 turn BE CAREFUL SO THAT THE REEL DOES NOT BEGIN TO SPIN FREELY! Lead back the hose through the outlet guide and fix the hose stop to the end of the outlet hose (Fig. 3). Fully unwind and rewind the hose completely to make sure that the spring is correctly tensioned. If the you need to adjust the tension of the spring, see Spring load adjustment. Sätt fast slangrullen i en bänk. För slangen genom slangrullens slangstyrning och sedan genom öppningen i trumman. Dra slangen genom trumman mot sviveln. Fäst slangen på sviveln enligt (2) i Fig 4 och montera U-bulten med muttrarna enligt (1) i samma figur. Rulla på hela slangen genom att vrida på trumman. När all slang är pårullad, förspänn slangrullens fjäder genom att vrida trumman ytterligare: För 15m slang: +8 varv, för 20m slang: +5 varv. För 25m slang: +5 varv, för 30m slang: +1 varv. VAR FÖRSIKTIG SÅ ATT RULLEN INTE BÖRJAR SNURRA FRITT! För slangen tillbaka genom slangstyrningen och montera slangstoppet på slangens fria ände (Fig. 3). Dra ut slangen helt och släpp tillbaka den för att försäkra att fjädern är tillräkligt spänd. Behövs fjädern spännas ytterligare; se avsnitt Justering av fjäderns spänning. Fig. 4 (EN) Hose replacement Warning! Before removing the hose, close the nearest shut off valve to the reel and open the fluid control gun to release the pressure inside the hose. (SE) Byte av slang Viktigt! Innan slangen monteras bort: stäng den från rullen sett närmaste ventilen samt öppna handventilen för att släppa på trycket i slangen. Unwind the hose completely and find the ratchet blocking position. BE CAREFUL SO THAT THE REEL DOES NOT BEGIN TO SPIN FREELY! Remove the hose stopper and the U-clamp(1, fig4). Disconnect the hose from the swivel(2, fig4) and remove the hose from the spool. Pass the new hose through the hose outlet and connect it to the swivel of the hose reel. Assemble the clamp and then the hose stopper at the required length. Pull the hose hard enough to release the latch, and slowly allow the hose to retract. Dra ut slangen helt och hitta spärrläget. VAR FÖRSIKTIG SÅ ATT RULLEN INTE BÖRJAR SNURRA FRITT! Ta bort slangstoppet och U-klammern (1, fig4). Lossa slangen från sviveln (2, fig4) och ta bort slangen från rullen. För den nya slangen genom slangstyrningen och anslut den till sviveln. Sätt tillbaka klammern samt montera slangstoppet på önskad höjd. Släpp spärren genom att dra i slangen och låt den sakta rulla upp sig på trumman. 4(9)
(EN) Spring load adjustment To increase or decrease spring tension 1. Pull out the hose to the first ratchet locking position. 2. Remove the hose stop. 3. Gently pull the hose until it is unlatched and slowly let it rewind applying counter force at all time to avoid the spool turning freely. 4. BE CAREFUL SO THAT THE REEL DOES NOT BEGIN TO SPIN FREELY! 5. Turn the spool in the direction shown in fig 5 to increase or decrease spring tension. 6. Pass the hose through the hose guide and let the ratchet lock the spool, replace the hose stop in desired position. 7. Repeat if more spring tension is required. (SE) Justering av fjäderns spänning För att öka eller minska fjäderns spänning 1. Dra ut slangen till den första låsta positionen. 2. Ta bort slangstoppet. 3. Dra försiktigt ut slangen tills spärren släpper och låt slangen rullas tillbaka på rullen, håll hela tiden ett stadigt tag i slangen. 4. VAR FÖRSIKTIG SÅ ATT RULLEN INTE BÖRJAR SNURRA FRITT! 5. Rotera rullen i riktning enligt fig.5 för att spänna eller lossa fjädern. 6. För tillbaka slangen genom slangstyrning och montera tillbaka slangstoppet i önskat läge. 7. Upprepa om mer spänning önskas. Fig. 5 Manual Hose Reel ORB, Rev 1a, 12-05-29
(EN) Swivel replacement Warning! Before removing the damaged swivel, close the nearest shut off valve to the reel and open the fluid control gun to release the pressure inside the hose. Disconnect the inlet hose (1). Unscrew the hose from the swivel using two spanners (2). Loosen the set screw in the locking nut (3), and remove the nut.). Remove the screws (4) and the arm (5). Replace the swivel with a new one or change the seals in the existing swivel. Make sure the seals are placed correctly, (fig 7). Grease the interior of the swivel and place it carefully back on to the shaft until it touches the bearing of the spool. Replace the rest of the parts in reverse order. (SE) Byte av svivel Viktigt! Innan sviveln byts, stäng den från rullen sett närmaste ventilen samt öppna handventilen för att släppa på trycket i slangen. Lossa inloppsslangen (1). Lossa slangen från rullen med hjälp av två fasta nycklar (2). Lossa låsskruven i kontramuttern och ta bort kontramuttern(3). Ta bort skruvarna(4) och armen(5). Byt ut sviveln eller byt packningar i befintlig svivel. Se till att packningarna hamnar på i rätt position, (Fig. 7). Smörj insidan av sviveln och för försiktigt tillbaka den över axeln. Montera ihop resterande delar. 2 Fig. 15 Fig. 7 3 Fig. 6 4 1 5 6(9)
(EN) Ratchet replacement Make sure the hose is completely wound on the spool and the hose stop is resting against the hose guide rollers. Remove the screws (1). Unscrew the ratchet shaft (2) and remove the ratchet assembly. Clean the parts or if necessary replace the parts. Re-assemble the pieces in reverse order. (SE) Byte av spärr Se till att slangen är helt inrullad och slangstoppet vilar mot slangstyrningsrullarna. Lossa skruvarna (1). Lossa spärraxeln (2) och ta loss spärren. Gör ren delarna eller om nödvändigt ersätt dem, och montera tillbaka. Fig. 8 (EN) Troubleshooting Symptom Possible causes Solution Hose does not rewind properly Spring has low load Adjust the spring load Leaking hose reel Damaged hose Replace the hose Leaking swivel Damaged swivel Replace the swivel Hose can not be pulled out as required Spring has too much load Adjust the spring load Hose reel does not latch Damaged ratchet Replace the ratchet Ratchet not fitted Assembly the ratchet properly Damaged ratchet spring Replace the ratchet spring (SE) Felsökning Symptom Orsak Åtgärd Slangen rullas inte tillbaka ordentligt Fjädern har för liten förspänning Spänn fjädern Läckande slang Skadad slang Byt slang Läckande svivel Skadad svivel Byt svivel Slangen kan inte dras ut hela vägen Fjädern är för spänd Släpp på fjäderns spänning Rullen spärras inte Skadad spärr Byt ut spärren Spärr felaktigt monterad Kontrollera hur spärren är monterad Skadad spärr-fjäder Byt ut fjäder 7(9)
(EN) Spare part drawing (SE) Reservdelsritning 8(9)
(EN) Spare parts list Hose Reel ORB For all models Description Art.no Incl. pos Contains For reel Roller outlet 2426460 17-24 17(x4), 18(x1), 19(x2), 20(x2), 21(x2),22(x2), 23(x2), 24(x4) All assembly Ratchet 2426461 1-7 1,2,3(x2),4,5,6,7 All Swivel seals 2326462 9,10 9,10 All Inlet shaft 2026463 12 11 All Description Art.no Incl. pos Contains For reel Swivel 2026464 8-10 8, 9,10 24977, 24978, 44453 (1 reels) 2026465 24975, 24976, 24979 (3/4 reels) 2026466 24974, 44452 (1/2 reels) Hose stop 2426467 13,14,16 13,14,16(x2) 24977, 24978, 44453 (1 reels) 2426468 24975, 24976, 24979 (3/4 reels) 2426469 24974, 44452 (1/2 reels) Description Art.no Incl. pos Contains For reel Power spring 2026470 11 11 24975, 24977, 24978, 44453 2026471 24974, 24976, 24979, 44452 (SE) Reservdelslista För alla modeller Beskrivning Art.nr Inkl.pos Innehåller För rulle Slangstyrning 2426460 17-24 17(x4), 18(x1), 19(x2), 20(x2), 21(x2),22(x2), 23(x2), 24(x4) Alla Spärr 2426461 1-7 1,2,3(x2),4,5,6,7 Alla Svivel 2326462 9,10 9,10 Alla packningar inloppsaxel 2026463 12 11 Alla Beskrivning Art.nr Inkl.pos Innehåller För rulle Svivel 2026464 8-10 8, 9,10 24977, 24978, 44453 (1 rullar) 2026465 24975, 24976, 24979 (3/4 rullar) 2026466 24974, 44452 (1/2 rullar) Slangstopp 2426467 13,14,16 13,14,16(x2) 24977, 24978, 44453 (1 rullar) 2426468 24975, 24976, 24979 (3/4 rullar) 2426469 24974, 44452 (1/2 rullar) Beskrivning Art.nr Inkl.pos Innehåller För rulle Fjäder 2026470 11 11 24975, 24977, 24978, 44453 2026471 24974, 24976, 24979, 44452 9(9)