Provläsningsexemplar / Preview SVENSK STANDARD SS-EN 1597-1 Handläggande organ Fastställd Utgåva Sida SVENSK MATERIAL- & MEKANSTANDARD, SMS 1998-03-20 1 1 (1+7+7) SIS FASTSTÄLLER OCH UTGER SVENSK STANDARD SAMT SÄLJER NATIONELLA, EUROPEISKA OCH INTERNATIONELLA STANDARDPUBLIKATIONER Welding consumables Test methods Part 1: Test piece for allweld metal test specimens in steel, nickel and nickel alloys Tillsatsmaterial för svetsning Provningsmetoder Del 1: Prov för helsvetsprovstavar i stål, nickel och nickellegeringar The European Standard has the status of a Swedish Standard. This document contains the official English version of with a Swedish translation. This standard has been developed in collaboration with the Swedish Welding Commission. This standard supersedes the Swedish Standards SS 06 10 01, edition 1, SS 06 11 01, edition 2 and SS 06 13 01, edition 1. Swedish Standards corresponding to documents referred to in this Standard are listed in Catalogue of Swedish Standards, issued by SIS. The Catalogue lists, with reference number and year of Swedish approval, International and European Standards approved as Swedish Standards as well as other Swedish Standards. Europastandarden gäller som svensk standard. Detta dokument innehåller den officiella engelska versionen av med svensk översättning. Denna standard har utarbetats i samarbete med Svetskommissionen. Standarden ersätter SS 06 10 01, utgåva 1, SS 06 11 01, SS 06 13 01, utgåva 1. Motsvarigheten och aktualiteten i svensk standard till de publikationer som omnämns i denna standard framgår av Katalog över svensk standard, som ges ut av SIS. I katalogen redovisas internationella och europeiska standarder som fastställts som svenska standarder och övriga gällande svenska standarder. ICS 25.160.20 Innehållet i svensk standard är upphovsrättsligt skyddat. SIS har copyright till svensk standard. Standarder kan beställas hos SIS som även lämnar allmänna upplysningar om svensk och utländsk standard. Postadress: SIS, Box 6455, 113 82 STOCKHOLM Telefon: 08-610 30 00. Telefax: 08-30 77 57 Upplysningar om sakinnehållet i standarden lämnas av SMS. Telefon: 08-459 56 00. Telefax: 08-667 85 42 E-post: info@sms-standard.se Prisgrupp P Tryckt i april 1998
Provläsningsexemplar / Preview EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM EN 1597-1 July 1997 ICS 25.160.20 Descriptors: welding, arc welding, steels, nickel, nickel alloys, fillers, weld metal, joining, preparation, test specimen, mechanical properties, classifications, tests English version Welding consumables Test methods Part 1: Test piece for all-weld metal test specimens in steel, nickel and nickel alloys Produits consommables pour le soudage Méthodes d essai Partie 1: Assemblage d essai d éprouvettes prélevées dans le métal fondu hors dilution pour le soudage de l acier, du nickel et des alliages de nickel Schweißzusätze Prüfmethoden Teil 1: Prüfstück zur Entnahme von Proben aus reinem Schweißgut an Stahl, Nickel und Nickellegierungen This European Standard was approved by CEN on 1997-06-29. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. No. E
EUROPASTANDARD EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM Provläsningsexemplar / Preview EN 1597-1 Juli 1997 ICS 25.160.20 Nyckelord: svetsning,bågsvetsning, stål, nickel, nickellegeringar, tillsatsmaterial, svetsgods, förbindning, fogberedning, provstav, mekaniska egenskaper, indelningar, prov Svensk version Tillsatsmaterial för svetsning Provningsmetoder Del 1: Prov för helsvetsprovstavar i stål, nickel och nickellegeringar Produits consommables pour le soudage Méthodes d essai Partie 1: Assemblage d essai d éprouvettes prélevées dans le métal fondu hors dilution pour le soudage de l acier, du nickel et des alliages de nickel Welding consumables Test methods Part 1: Test piece for all-weld metal test specimens in steel, nickel and nickel alloys Schweißzusätze Prüfmethoden Teil 1: Prüfstück zur Entnahme von Proben aus reinem Schweißgut an Stahl, Nickel und Nickellegierungen Denna standard är den officiella svenska versionen av. För översättningen svarar SIS. Denna europastandard antogs av CEN 1997-06-29. CEN-medlemmarna är förpliktade att följa fordringarna i CEN/CENELECs interna bestämmelser som anger på vilka villkor denna europastandard i oförändrat skick skall ges status som nationell standard. Aktuella förteckningar och bibliografiska referenser rörande sådana nationella standarder kan på begäran erhållas från CENs centralsekretariat eller från någon av CENs medlemmar. Denna europastandard finns i tre officiella versioner (engelsk, fransk och tysk). En version på något annat språk, översatt under ansvar av en CEN-medlem till sitt eget språk och anmäld till CENs centralsekretariat, har samma status som de officiella versionerna. CENs medlemmar är de nationella standardiseringsorganen i Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike. CEN European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 36, B-1050 BRUSSELS 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members Ref. Nr. Sv
Page 2 Provläsningsexemplar / Preview Contents Page Foreword... 3 Introduction... 4 1 Scope... 4 2 Normative references... 4 3 General requirements... 4 4 Test plate material... 4 5 Preparation of test piece... 5 6 Welding conditions... 5 7 Heat treatment... 6 8 Position of specimens and specimen dimensions... 6 9 Retests... 6 10 Test report... 7
Provläsningsexemplar / Preview Sida 2 Innehåll Sida Förord... 3 Orientering... 4 1 Omfattning... 4 2 Bindande referenser... 4 3 Allmänna krav... 4 4 Provplåtar... 4 5 Provstycke... 5 6 Svetsningsbetingelser... 5 7 Värmebehandling... 6 8 Läge och mått för provstav... 6 9 Omprov... 6 10 Provningsrapport... 7
Page 3 Provläsningsexemplar / Preview Foreword This European Standard has been prepared by Technical Committee CEN/TC 121 Welding, the secretariat of which is held by DS. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1998, and conflicting national standards shall be withdrawn at the latest by January 1998. This standard consists of the following parts: Part 1: Test piece for all-weld metal test specimens in steel, nickel and nickel alloys Part 2: Preparation of test piece for single-run and two-run technique test specimens in steel Part 3: Classification testing of positional capability of welding consumables in a fillet weld According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Provläsningsexemplar / Preview Sida 3 Förord Denna europastandard har utarbetats av den tekniska kommittén CEN/TC 121 Welding med sekretariat vid DS. Denna europastandard skall ges status som nationell standard, antingen genom publikation av en identisk text eller genom ikraftsättning, senast i januari 1998. Motstridande nationella standarder skall dras in senast i januari 1998. Denna standard består av följande delar: Del 1: Prov för helsvetsprovstav i stål, nickel och nickellegeringar Del 2: Framställning av prov för provstavar i ensträngs- och tvåsträngsteknik i stål Del 3: Provning av lägessvetsbarhet hos svetstillsatsmaterial i en kälsvets Enligt CEN/CENELECS interna bestämmelser är följande länder förpliktade att införa denna europastandard: Belgien, Danmark, Finland, Frankrike, Grekland, Irland, Island, Italien, Luxemburg, Nederländerna, Norge, Portugal, Schweiz, Spanien, Storbritannien, Sverige, Tjeckien, Tyskland och Österrike.
Page 4 Provläsningsexemplar / Preview Introduction It should be noted that the mechanical properties of all-weld metal test specimens used to classify the welding consumables could vary from those obtained in production joints because of differences in welding procedure such as electrode diameter, width of weave, welding position and material composition. Test conditions prescribed and results required should not be considered to be requirements or expectations for a procedure qualification. 1 Scope This standard specifies preparation of test piece and specimens. The purpose is to determine mechanical properties of all-weld metal where required by the consumable classification standard or for other purposes in arc welding of steel, nickel and nickel alloys. This standard is not applicable to single- or two-pass welding or fillet welding. For these cases, EN 1597-2 and EN 1597-3 apply. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 875 Destructive tests on welds in metallic materials Impact tests Test specimen location, notch orientation and examination EN 876 EN 1597-2 EN 1597-3 Destructive tests on welds in metallic materials Longitudinal tensile test on weld metal in fusion welded joints Welding consumables Test methods Part 2: Preparation of test piece for single and two run technique test specimens in steel Welding consumables Test methods Part 3: Classification testing of positional capability of welding consumables in a fillet weld EN ISO 13916 Welding Guidance on the measurement of preheating temperature, interpass temperature and preheat maintenance temperature (ISO 13916:1996) 3 General requirements Welding consumables to be tested shall be representative of the manufacturer's products to be classified or tested. Test pieces shall be prepared as described below. 4 Test plate material The material to be used for the test piece shall be compatible with the weld metal provided by the welding consumable tested. Alternatively the groove edges and the backing strip shall be built up with at least two layers using the welding consumable being tested.