SVENSK STANDARD SS :2014

Transkript

1 SVENSK STANDARD SS :2014 Fastställd/Approved: Publicerad/Published: Utgåva/Edition: 2 Språk/Language: engelska/english ICS: ; Produktspecifikation för SS-EN 10080:2005 Armeringsstål Svetsbart armeringsstål Tekniska leveransbestämmelser för stång, coils, svetsat nät och armeringsbalk Product specification for SS-EN 10080:2005 Steel for the reinforcement of concrete Weldable reinforcing steel Technical delivery conditions for bars, coils, welded fabric and lattice girders

2 Standarder får världen att fungera SIS (Swedish Standards Institute) är en fristående ideell förening med medlemmar från både privat och offentlig sektor. Vi är en del av det europeiska och globala nätverk som utarbetar internationella standarder. Standarder är dokumenterad kunskap utvecklad av framstående aktörer inom industri, näringsliv och samhälle och befrämjar handel över gränser, bidrar till att processer och produkter blir säkrare samt effektiviserar din verksamhet. Delta och påverka Som medlem i SIS har du möjlighet att påverka framtida standarder inom ditt område på nationell, europeisk och global nivå. Du får samtidigt tillgång till tidig information om utvecklingen inom din bransch. Ta del av det färdiga arbetet Vi erbjuder våra kunder allt som rör standarder och deras tillämpning. Hos oss kan du köpa alla publikationer du behöver allt från enskilda standarder, tekniska rapporter och standardpaket till handböcker och onlinetjänster. Genom vår webbtjänst e-nav får du tillgång till ett lättnavigerat bibliotek där alla standarder som är aktuella för ditt företag finns tillgängliga. Standarder och handböcker är källor till kunskap. Vi säljer dem. Utveckla din kompetens och lyckas bättre i ditt arbete Hos SIS kan du gå öppna eller företagsinterna utbildningar kring innehåll och tillämpning av standarder. Genom vår närhet till den internationella utvecklingen och ISO får du rätt kunskap i rätt tid, direkt från källan. Med vår kunskap om standarders möjligheter hjälper vi våra kunder att skapa verklig nytta och lönsamhet i sina verksamheter. Vill du veta mer om SIS eller hur standarder kan effektivisera din verksamhet är du välkommen in på eller ta kontakt med oss på tel Standards make the world go round SIS (Swedish Standards Institute) is an independent non-profit organisation with members from both the private and public sectors. We are part of the European and global network that draws up international standards. Standards consist of documented knowledge developed by prominent actors within the industry, business world and society. They promote cross-border trade, they help to make processes and products safer and they streamline your organisation. Take part and have influence As a member of SIS you will have the possibility to participate in standardization activities on national, European and global level. The membership in SIS will give you the opportunity to influence future standards and gain access to early stage information about developments within your field. Get to know the finished work We offer our customers everything in connection with standards and their application. You can purchase all the publications you need from us - everything from individual standards, technical reports and standard packages through to manuals and online services. Our web service e-nav gives you access to an easy-to-navigate library where all standards that are relevant to your company are available. Standards and manuals are sources of knowledge. We sell them. Increase understanding and improve perception With SIS you can undergo either shared or in-house training in the content and application of standards. Thanks to our proximity to international development and ISO you receive the right knowledge at the right time, direct from the source. With our knowledge about the potential of standards, we assist our customers in creating tangible benefit and profitability in their organisations. If you want to know more about SIS, or how standards can streamline your organisation, please visit or contact us on phone +46 (0)

3 Standarden har utgivits i svensk språkversion De båda språkversionerna gäller parallellt. Denna standard ersätter SS :2011, utgåva 1. This standard was published in Swedish The two versions are valid in parallel. This standard supersedes the Swedish Standard SS :2011, edition 1. Copyright/Upphovsrätten till denna produkt tillhör SIS, Swedish Standards Institute, Stockholm, Sverige. Användningen av denna produkt regleras av slutanvändarlicensen som återfinns i denna produkt, se standardens sista sidor. Copyright SIS, Swedish Standards Institute, Stockholm, Sweden. All rights reserved. The use of this product is governed by the end-user licence for this product. You will find the licence in the end of this document. Upplysningar om sakinnehållet i standarden lämnas av SIS, Swedish Standards Institute, telefon Standarder kan beställas hos SIS Förlag AB som även lämnar allmänna upplysningar om svensk och utländsk standard. Information about the content of the standard is available from the Swedish Standards Institute (SIS), telephone Standards may be ordered from SIS Förlag AB, who can also provide general information about Swedish and foreign standards. Standarden är framtagen av kommittén för Armering, SIS/TK 145. Har du synpunkter på innehållet i den här standarden, vill du delta i ett kommande revideringsarbete eller vara med och ta fram andra standarder inom området? Gå in på - där hittar du mer information.

4 Contents Introduction Scope Normative references Terms and definitions Symbols Designation Performance characteristics Mechanical properties Tensile properties Shear force of welded or clamped joints Fatigue strength Suitability for bending Bond strength and surface geometry General Surface geometry of ribbed steel Surface geometry of indented steel Factory production control General Evaluation of test results Traceability Identification of the manufacturer and the technical class... 8 Annex A (normative) Delivery documents... 9 Annex B (informative) Abbreviation of designations for product type and geometry, delivery condition and product form for bars Annex C (informative) Reinforcing steels with characteristic yield strength 500MP Bibliography Page 2

5 Introduction The European Standard for reinforcing steel - EN was approved by CEN and published as an SS-EN Standard in May EN specifies general requirements and testing methods for reinforcing steel but should be complemented by product specifications. The European Commissions Standing Committee on Construction (SCC) did not approve EN so it is not a harmonized standard according to the Construction Products Regulation (CPR). This standard has been prepared because the Swedish Standards for weldable reinforcing steel needed to be revised and EN contains no technical classes. The requirements in the standard are consistent with the requirements for reinforcing steel in SS-EN :2005 and the Swedish national choices. Revision of EN 10080:2005 has started within CEN. When the revised edition of EN 10080:2005 is approved SS may be withdrawn. 3

6 1 Scope This Swedish Standard specifies values not given in SS-EN 10080:2005 and shall be applied in association with SS-EN 10080:2005. The number of the clauses are the same as in SS-EN 10080:2005. When there are no choices or specifications made for a clause in SS-EN 10080:2005 the clause does not appear in SS and its table of contents. NOTE Tables in this standard have numbers S1, S2 etc. to separate them from the tables in SS-EN Annexes in SS have no connection to annexes in SS-EN 10080:2005. Annex C (informative) summarizes the properties of four technical classes with characteristic yield strength 500MPa and different ductility. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. SS-EN 10080:2005 Steel for the reinforcement of concrete Weldable reinforcing steel General SS-EN :2005 Eurocode 2: Design of concrete structures Part 1-1: General rules and rules for buildings SS-EN Metallic materials. Types of inspection documents NOTE When applying SS-EN the Swedish national choices made in BFS 2008:8-EKS or VVFS 2004:43 (including later changes to these documents) shall be applied. 3 Terms and definitions For the purposes of this standard the terms and definitions given in SS-EN 10080:2005 apply. 4 Symbols The symbols used in SS-EN 10080:2005 are used in this standard. 5 Designation The products covered by this standard shall be designated, in Swedish or English, according to SS-EN 10080:2005 and the following. The designation consists of three parts: a) Product form, surface geometry and the designation EN 10080, b) the nominal dimensions of the product, c) the designation of this standard, SS , the characteristic yield strength and class of the steel according to Table S1 and as optional information, the delivery condition and if the products are decoiled/not decoiled can be part of the designation. EXAMPLE Ribbed bars SS-EN x12000 SS B hot rolled and immediately heat treated in line. Normally the designer does not specify delivery condition or decoiled/not decoiled in the design documentation. EXAMPLE Ribbed bars SS-EN x SS B. NOTE Abbreviation of the designation according to Annex B may be used. 4

7 7 Performance characteristics 7.2 Mechanical properties Tensile properties This standard specifies the tensile properties R e, R m /R e, och A gt. These properties shall fulfil the requirements in Table S1. SS-EN 10080:2005 also applies. Table S1 Tensile properties Yield strength R e MPa Stress ratio R m/r e Class A AB B C ,05 1,08 1,08 1,15 < 1,35 Type of specified value C v p = 0,95 C v p = 0,90 Elongation at maximum load A gt % 2,5 3,0 5,0 7,5 C v p = 0,90 NOTE The properties specified in table S1 for classes A, B and C are in conformity with SS-EN :2005, annex C. Class AB is a class adapted to Swedish practice Shear force of welded or clamped joints Welded fabric The minimum value of the shear force for welded joints shall not be less than 0,25 R e A n where A n is the nominal cross-sectional area of either: a) the larger wire at the joint in a single wire welded fabric, b) one of the twin wires in a twin wire welded fabric (twin wires in one direction) Lattice girders Welded joints The minimum value of the shear force strength of a weld point shall not be less than 0,25 R e,ch A Ch 0,6 R e,di A Di whichever is the lower. or Fatigue strength Axial force controlled fatigue testing shall be performed if the purchaser so specifies at the time of order. If submitted to fatigue testing the product shall withstand stress cycles with stress that varies sinusoidally over the range of stress 2σ a from the maximum stress σ max. 2σ a and σ max shall be according to Table S2. However greater values for the range of stress or the number of stress cycles, may be declared if confirmed by testing according to SS-EN 10080:

8 Table S2 Range of stress and maximum stress Stresses Rolled or decoiled bars Welded fabric Type of specified value 2σ a 150 MPa 100 MPa C v σ max 0,6 R e 0,6 R e p = 0,90 NOTE R e is the specified characteristic value for the yield strength Suitability for bending Suitability for bending shall be determined by at least the bend test NOTE BFS 2008:8-EKS and VVFS 2004:43 specify the testing required for using smaller mandrel diameters when bending than specified in SS-EN The bend test shall be performed with mandrel diameter according to Table S3. Table S3 Mandrel diameter for the bend test Nominal diameter d mm Mandrel diameter max Angle of bend γ min 4 d 10 1,5 d 10 < d 20 2,0 d < d 32 3,0 d 32 < d 50 4,0 d The re-bend test, if required, shall be performed with mandrel diameter according to SS-EN 10080: Bond strength and surface geometry General Bond property requirements of ribbed and indented reinforcing steels shall be based on surface geometry. Alternatively, bond property requirements of ribbed and indented reinforcing steel may be determined by appropriate bond tests, see C.1.(1) in SS-EN :2005. Testing and verification of surface geometry parameters shall be performed according to SS-EN 10080:

9 7.4.2 Surface geometry of ribbed steel Transverse ribs shall conform to the requirements in SS-EN 10080:2005. f R shall fulfil the requirements in Table S4. Table S4 f R for transverse ribs Nominal diameter d mm f R Type of specified value 5,0 d 6,0 0,035 Cv p = 0,95 6,5 d 12 0,040 Cv p = 0,95 d > 12 0,056 Cv p = 0, Surface geometry of indented steel Indentations shall conform to the requirements in SS-EN 10080:2005. There is no required f p - value. 8 Evaluation of conformity 8.1 Factory production control General NOTE According to BFS 2008:8 EKS with amendments, products according to this standard are products with confirmed properties only when product certified Evaluation of test results R e, A gt and R m /R e C v specified as a lower limit At least one of the following conditions for R e, A gt and R m /R e shall be satisfied: a) All individual values are greater than specified C v for R e, R m /R e och A gt. b) given that at least 8 tests have been performed, mean and individual values for R e, R m /R e och A gt are according to Table S6. 7

10 Tabell S5 Individual values and mean values given at least 8 tests Property Individual values when maximum values are specified Mean values when maximum values are specified R e 0,97 C v C v + 10 MPa R m /R e 0,98 C v C v A gt 0,95 C v C v C v specified as an upper limit At least one of the following conditions for R m /R e shall be satisfied: a) All individual values are lower than or equal to C v for R e, R m /R e och A gt. b) given that at least 8 tests have been performed, mean and individual values for R m /R e are according to Table S5. Tabell S6 Individual values and mean values given at least 8 tests Property R m /R e a Individual values when minimum values are specified 1,02 C v Mean values when minimum values are specified C v a Only relevant for class C Traceability The delivered products shall be traceable to their production data. The products shall be accompanied by documents according to Annex A. 10 Identification of the manufacturer and the technical class Delivered products shall be accompanied by a weather-resistant label containing the following information: number of this standard, name of the manufacturer or de-coiler, designation of the product and technical class, nominal dimensions and weight of the bundle, information giving traceability to production data name or mark of the product certification body and number of the product certificate. The label may also contain other information according to agreement between manufacturer and purchaser. 8

11 Annex A (normative) Delivery documents A.1 Inspection document Bars and coils shall be accompanied by an inspection certificate 3.1 according to SS-EN De-coiled bars, welded fabric and lattice girders are not accompanied by an inspection document unless otherwise agreed at the time of order. A.2 Delivery note Each delivered batch shall be accompanied by a delivery note containing the following information: consignee, manufacturer, designation of the product, delivered quantity, information giving traceability to production data date of delivery. 9