INSTALLATION INSTRUCTIONS

Storlek: px

Starta visningen från sidan:

Download "INSTALLATION INSTRUCTIONS"

Anton Dahlberg
för 4 år sedan
Visningar:

1 INSTALLATION - REEIVER INSTALLATION INSTRUTIONS RT0 RF WIRELESS ROOM THERMOSTAT AND REEIVER MOUNTING OF WALL MOUTING PLATE - Unscrew the screws under the - Pack contains... Installation - Receiver... Mounting of wall mouting plate... Wiring... Mounting of the receiver... Installation - Thermostat... Installing batteries... Mounting of thermostat... Pairing procedure...3 Troubleshooting PAK ONTAINS WIRING are not sure how to install this thermostat consult either with a All wiring must be in accordance with IEE regulations. This product is for Thermostat Receiver Thermostat table stand N L 3 4 AA Batteries (LR6) Screw Anchor Screws N = Neutral L = Live = Not used = Normally closed 3 = ommon RTE0RFA NEO ENG FP V

2 MOUNTING OF THE REEIVER INSTALLATION - THERMOSTAT INSTALLING BATTERIES 5- Secure the thermostat by - Remove the batteries cover - - On the table stand - - Fold the stand and lock it into MOUNTING OF THERMOSTAT On the wall - Unscrew the screws under the -

3 NB: Important: - PAIRING PROEDURE - - onds the RF test button on the 3- Thermostat RF and recei- TROUBLESHOOTING Thermostat RF and re- - - onds the RF test button Do not use rechargeable batteries. The heating does not come on or does not go off. section on - The receiver does not recognize transmitter s code. The radio link between the thermostat and the receiver is lost. TEHNIAL SPEIFIATIONS Receiver: Signal sending: Standards: Transmitter Receiver R&TTE EM RoHS R&TTE-EM RoHS EN63 EN EN EN EN6479 EN EN Environment : N.B.: The 3

4 LD Display Low battery OPERATING INSTRUTIONS Measured room temperature RT0 RF WIRELESS ROOM THERMOSTAT AND REEIVER Pairing Frost protection Temperature setpoint SETTINGS INITIAL POWER UP Overview... ontrols and display... Settings... Initial power up... Pairing procedure... Operating... Temperatures setting... Factory settings... Troubleshooting What is a room thermostat... OVERVIEW have created and designed our products It is this ease of operation that is intended energy and money. - To start: insert the two AA batteries provided into the battery compartment. the LD screen as shown for two seconds. - show: - The ambient temperature ( ) - The heating is turned ON. - The setpoint temperature ( ) Note: appears on the device. PAIRING PROEDURE The thermostat and the receiver are not bonded together at the factory. - onds the RF test button on the - for onds the RF test button on the thermostat. Pairing ONTROLS AND DISPLAY Thermostat Batteries compartment RF test button Reset button RTE0RFa NEO ENG FP V

5 3- Thermostat RF and recei- 4- Thermostat RF and re- The room temperature is not high enough, the boiler is not providing enough heat: - heck the active desired temperature and increase it if need be (see page ). You made a mistake while setting: settings section (see page ) have made. The system is not heating but is on: - If If the problem persists, then contact your installer. OPERATING TEHNIAL SPEIFIATIONS - TEMPERATURES SETTING The desired temperature can be set. - - ture. FATORY SETTINGS Settings Factory settings Set temperature 0 than 3 seconds using the tip of a pen. restored. TROUBLESHOOTING The boiler is not heating: off. If no increase set temperature. - heck the position of the batteries. Remove them for 30 seconds and Nothing in the display: - heck the position of the batteries. Remove them for 30 seconds and WHAT IS A ROOM THERMOSTAT the heating system on and off as necessary. It works by sensing the air temperature, switching on the heating when the air temperature and switching it off once this set temperature has been reached. Turning a room thermostat to a hi- - - energy and cost you more money. - reating innovative solutions for ambient comfort NEOMITIS LIMITED - 4th Floor, Lincoln House, 300 High Holborn, London WV 7JH Registered in England and Wales No: Tel: +44 (0) Fax: +44 (0) contact_uk@neomitis.com Registered trademarks - All rights reserved

Relevanta dokument

Support Manual HoistLocatel Electronic Locks

Support Manual HoistLocatel Electronic Locks 1. S70, Create a Terminating Card for Cards Terminating Card 2. Select the card you want to block, look among Card No. Then click on the single arrow pointing